技术资料

山高铰刀,PRECIMASTER HOLDERS铰孔刀具06

2020-05-29 14:09:30 daoju

5) 将.头推 .体,直到发出“咔嗒声”

6) 夹紧刀头(参见推荐扭矩值)

PMX .杆尺.PMX05 PMX06 PMX08 PMX12 推荐夹紧扭矩 0,5 Nm 0,9 Nm 1,2 Nm 2,0 Nm

跳动量 - 设定 旋转式刀具

推荐大跳动量:10-15 μm。 推荐使用液压夹头、热胀刀柄或高精度弹簧夹头。为实现佳跳动量控制,我们推荐使用 Precimaster Plus PMX-AD 可调转接头,参见第 253-254 页。

冷却液要求

为获得佳的刀具寿命与孔径,应遵循下列冷却液要求。推荐使.内冷却。如果铰削深度 < 2 x D,则可以使.外部冷却液供应。矿物油含量少为 40% 的优质可溶油。加.不锈钢时推荐使.纯矿物油。.浓度为 6–8%。过滤 30–50 μm。对于铰.直径.言,.流量为 0,5 l/min/mm。(例:铰.直径为 . 10,.流量为 5 l/min)。

直径测量

在测量直径 . 之前校准千分尺。

重要!

Precimaster 铰刀的齿距是不等分的。在测量直径时,确保 2 个刀齿成 180° 夹角。

使用千分尺和量块进行测量。

Precimaster Plus 调节.杆设置:

1. 将刀具安装到机床主轴上

2. 如图所示,设置千分表

3. 手动旋转刀具,直到达到点

4. 如箭头所示,使用调节螺钉进行跳动量补偿。

5. 检查跳动量并在必要时重复补偿

6. 当大跳动小于 5 μm 时,锁紧调整螺钉以避免调整值松动

Precimaster Plus 浮动.杆设置:

1. 顺时针将浮动铰刀杆调整环完全拧紧

2. 逆时针将调整环转 2 到 3 格从而使刀杆开始浮动

3. 如有必要,可进一步调整浮动值浮动值过大可能会造成入孔时不稳定。浮动值过少可能会造成振动和锥孔。

Precimaster Plus 可胀式铰.磨损补偿:

1. 使用六角扳手来补偿刀具直径磨损(旋转 60°= 直径方向补偿约 5 μm)

2. 用千分尺检查补偿后的直径尺寸

.头选择 - 根据应.场合与直径选择.头类型

.件 铰削直径 . 10-60

短通孔 < 3 x D PMX5 / PMX8

长通孔 > 3 x D PMX6 对于通孔应用,必须为通孔设置刀柄冷却液出口:请参见冷却液设置页

贯穿孔

盲孔 PMX5 / PMX8 对于盲孔应用,必须为盲孔设置刀柄冷却液出口:请参见冷却液设置页

盲孔与贯穿孔

槽型选择 - 应.

导向槽型 - EB845

切屑控制 ++表面粗糙度 +++ (Ra 0,2 - 0,8 m)

导向槽型 - EB25

进给性能 +++表面粗糙度 ++ (Ra 0,4 - 0,8 m)切屑控制 +

材质等级

CP20 镀层适用于除铝合金外的大多数材料的通用镀层材质等级。 TiN

H15 未镀层适用于所有材料的韧性好的细颗粒材质等级。因其锋利的切削刃,适用于精密铰削加工。

CF 金属陶瓷针对钢件加工时优化性能的耐磨材质等级。

RX1500 镀层金属陶瓷针对钢件与铸铁加工时优化性能的耐磨材质等级。

RX2000 镀层适用于所有材料的高性能镀层材质等级。

RN2010 槽型对N组材料(有色金属)进行优化的未涂层亚细晶粒材质。

RM2020 槽型对M组材料进行优化的高韧性涂层材质,适用于精密铰削加工。

RM2090 槽型对M组材料进行特殊优化的高耐磨性涂层材质。

RS2090 槽型对S组材料进行特殊优化的高耐磨性涂层材质。

.于直径 .8-32 mm 通孔和盲孔的.头

.关于切削参数,参见第 264-265 页

.关于导向槽型 EB45、EB845 或 EB25 的选择,参见第 247 页

DC8,0 钻头规格*7,8/7,9 产品型号

PMX5-8H7-EB45

6 LFS 6,0 DMM4,5 .体规格PMX05-xx 槽型 材质等级

[EB45 ]EB845 ] EB25 ] H15 ] CP20 03123158

RX2000 ] CF ] RX1500

9,0 8,8/8,9 PMX5-9H7-EB45

6 6,0 4,5 PMX05-xx ] ] ] ] 03123159

] ]

10,0 9,8/9,9 PMX5-10H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02965840

02965923

]

11,0 10,8/10,9 PMX5-11H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02925754

12,0 11,8/11,908 PMX5-12H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02925755

02925041

13,0 12,8/12,9 PMX5-13H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02925756

02925042

14,0 13,8/13,891 PMX5-14H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02925757

02925043

15,0 14,8/14,9 PMX5-15H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925758

02925044

16,0 15,8/15,9 PMX5-16H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925759

02925045

17,0 16,8/16,9 PMX5-17H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925760

02925046

18,0 17,8/17,9 PMX5-18H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925761

02925047

19,0 18,8/18,9 PMX5-19H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925762

20,0 19,8/19,9 PMX5-20H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925763

02925048

21,0 20,8/20,9 PMX5-21H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925764

22,0 21,8/21,9 PMX5-22H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925765

02925049

23,0 22,8/22,9 PMX5-23H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925766

24,0 23,813/23,9 PMX5-24H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925767

02925050

25,0 24,8/24,9 PMX5-25H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925768

02925051

26,0 25,8/25,9 PMX5-26H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925769

02925052

27,0 26,8/26,9 PMX5-27H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925770

28,0 27,8/27,9 PMX5-28H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925771

02925053

29,0 28,8/28,9 PMX5-29H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925772

30,0 29,8/29,9 PMX5-30H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925773

02925054

31,0 30,8/30,9 PMX5-31H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925774

32,0 31,8/31,9 PMX5-32H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925775

02925055

* 关于钻头选用以及使用说明的更多信息,参见第 9 页

标准库存 ] 非标准库存。供货情况请参阅新的价格和库存表。

直径 .8-32 mm 通孔的.头

PMX6-8H7-EB45

EB45]EB845 ] EB25 ] H15 ] CP20 03123161

9,0 8,8/8,9 PMX6-9H7-EB45

6 6,0 4,5 PMX05-xx ] ] ] ] 03123162

10,0 9,8/9,9 PMX6-10H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02965863

11,0 10,8/10,9 PMX6-11H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02925776

12,0 11,8/11,908 PMX6-12H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02925777

13,0 12,8/12,9 PMX6-13H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02925778

14,0 13,8/13,891 PMX6-14H7-EB45

6 7,0 6,0 PMX06-xx ] ] ] ] 02925779

15,0 14,8/14,9 PMX6-15H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925780

16,0 15,8/15,9 PMX6-16H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925781

17,0 16,8/16,9 PMX6-17H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925782

18,0 17,8/17,9 PMX6-18H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925783

19,0 18,8/18,9 PMX6-19H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925784

20,0 19,8/19,9 PMX6-20H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925785

21,0 20,8/20,9 PMX6-21H7-EB45

6 10,0 8,0 PMX08-xx ] ] ] ] 02925786

22,0 21,8/21,9 PMX6-22H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925030

23,0 22,8/22,9 PMX6-23H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925031

24,0 23,813/23,9 PMX6-24H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925032

25,0 24,8/24,9 PMX6-25H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925033

26,0 25,8/25,9 PMX6-26H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925034

27,0 26,8/26,9 PMX6-27H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925035

28,0 27,8/27,9 PMX6-28H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925036

29,0 28,8/28,9 PMX6-29H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925037

30,0 29,8/29,9 PMX6-30H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925038

31,0 30,8/30,9 PMX6-31H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925039

32,0 31,8/31,9 PMX6-32H7-EB45

8 12,0 12,0 PMX12-xx ] ] ] ] 02925040

* 关于钻头选用以及使用说明的更多信息,参见第 9 页 [标准库存 ]非标准库存。供货情况请参阅新的价格和库存表。

.于直径 .7,75-60,500 mm 通孔和盲孔的.杆

DC7,75-9,99,901-14,49914,5-21,49921,5-32,49932,5-60,5 .杆材料钢制 订购代码03123012

产品型号PMX05-02800-10N1

OAL 69 LB 63 LS 40 LUX 28 DMM 10

钢制 02929923

PMX05-04100-10N1

84 78 40 41 10

钢制 钢制 03123013

02925828

PMX05-10000-10N1

PMX06-03700-12N1

143 84 137 77 40 45 100 37 10 12

钢制 02925829

PMX06-05700-12N1

104 97 45 57 12

钢制 02925830

PMX06-12000-12N1

167 160 45 120 12

硬质合金 钢制 02925831

02925832

PMX06HM-12000-12N1

PMX08-04600-20N1

167 99 160 89 45 50 120 46 12 20

钢制 02925833

PMX08-08200-20N1

135 125 50 82 20

钢制 02925834

PMX08-14500-20N1

198 188 50 145 20

硬质合金 钢制 02925835

02925836

PMX08HM-14500-20N1

PMX12-06800-25N1

198 127 188 115 50 56 145 68 20 25

钢制 02925837

PMX12-10400-25N1

163 151 56 104 25

钢制 02925838

PMX12-17000-25N1

229 217 56 170 25

硬质合金 钢制 02925839

02925840

PMX12HM-17000-25N1

PMX16-06300-32N1

229 124 217 110 56 61 170 63 25 32

钢制 02925841

PMX16-12700-32N1

188 174 61 127 32

钢制 02925842

PMX16-17000-32N1

231 217 61 170 32

硬质合金 02925843

PMX16HM-17000-32N1

适. 适.直径 压板扳. 压板套装 冷却套装 堵头螺钉,盲孔 堵头螺钉,通孔

.杆PMX05 (mm)7,75-9,900 1.5SMS795 PMX05-CLKI

RT05-KI

SB05

ST05

PMX06 9,901-14,499 2SMS795

PMX06-CLKI

RT06-KI

SB06

ST06

PMX08 14,5-21,499 2.5SMS795

PMX08-CLKI

RT08-KI

SB08

ST08

PMX12 21,5-32,499 4SMS795

PMX12-CLKI

RT12-KI

SB12

ST12

PMX16 32,5-60 5SMS795

PMX16-CLKI

– SB16

ST16

* PMX16 铰刀杆专用备件,冷却管螺钉也用于锁紧。关于附件,请参见第 253 页

盲孔.杆 . 7,75-60,500

DC7,75-9,99,901-14,49914,5-21,49921,5-32,49932,5-60,5 .杆材料钢制 订购代码03144322

产品型号PMX05B-02800-10N1

钢制 03144323

PMX05B-04100-10N1

钢制 钢制 03144324

03075433

PMX05B-10000-10N1

PMX06B-03700-12N1

钢制 03075434

PMX06B-05700-12N1

钢制 03075435

PMX06B-12000-12N1

硬质合金 钢制 03075436

03075437

PMX06BHM-12000-12N1

PMX08B-04600-20N1

钢制 03075438

PMX08B-08200-20N1

钢制 03075439

PMX08B-14500-20N1

硬质合金 钢制 03075440

03075441

PMX08BHM-14500-20N1

PMX12B-06800-25N1

钢制 03075442

PMX12B-10400-25N1

钢制 03075443

PMX12B-17000-25N1

硬质合金 钢制 03075444

03075445

PMX12BHM-17000-25N1

PMX16B-06300-32N1

钢制 03075446

PMX16B-12700-32N1

钢制 03075447

PMX16B-17000-32N1

硬质合金 03075448

PMX16BHM-17000-32N1

适 .杆PMX05B 适.直径 (mm)7,75-9,900 压板扳.1.5SMS795 压板套装 PMX05-CLKI

堵头螺钉,盲孔 SB05

PMX06B 9,901-14,499 2SMS795

PMX08B 14,500-21,499 2.5SMS795

PMX12B 21,500-32,499 4SMS795

PMX16B 32,500-60,000 5SMS795

SB16

.于直径 .10-60,500 mm 通孔的可调.杆

DC7,75-9,9 订购代码03271918

产品型号PMX05T-AD-04100-16N1

OAL 102 LB 96 LS 48 LUX 41 BDX 18 DMM 16

9,901-14,499 03002833

PMX06T-AD-05700-16N1

117 110 48 57 18 16

14,5-21,499 03002835

PMX08T-AD-08200-20N1

147 137 50 82 22 20

21,5-32,499 03002837

PMX12T-AD-10400-25N1

179 167 56 104 28 25

32,5-60,5 03002839

PMX16T-AD-12700-32N1

214 200 60 127 34 32

适 .杆PMX05T 适.直径 (mm)7,750-9,900 压板扳.1.5SMS795 冷却环 RT05-KI

调整扳.2SMS795

对.块

PMX05-MSTR

PMX06T 9,901-14,499 2SMS795

2SMS795

PMX06-MSTR

PMX08T 14,50-21,499 2.5SMS795

2.5SMS795

PMX08-MSTR

PMX12T 21,50-32,499 4SMS795

3SMS795

PMX12-MSTR

PMX16T 32,50-60,000 5SMS795

– 3SMS795

附件

. 范围7,750-9,900 .杆尺.PMX05 订购代码03178237

可换扳.芯H00-1.5-27

订购代码03178196

扭矩扳.H00-1505-24

扭矩值 0,5 Nm

9,901-14,499 PMX06 03178238

H00-2.0-33

03178197

H00-2009-33

14,500-21,499 PMX08 03178240

H00-2.5-40

03178199

H00-2512-40

21,500-32,499 PMX12 03178242

H00-4.0-60

03178201

H00-4020-60

.于直径 .10-60,500 mm 盲孔的可调.杆

DC7,75-9,9 订购代码03271919

产品型号PMX05B-AD-04100-16N1

9,901-14,499 03002834

PMX06B-AD-05700-16N1

14,5-21,499 03002836

PMX08B-AD-08200-20N1

21,5-32,499 03002838

PMX12B-AD-10400-25N1

32,5-60,5 03002840

PMX16B-AD-12700-32N1

适 .杆PMX05B 适.直径 (mm)7,750-9,900 压板扳. 1.5SMS795 调整扳. 2SMS795

对.块 PMX05-MSTR

– PMX06-MSTR

PMX08B 14,50-21,499 2.5SMS795

– PMX08-MSTR

PMX12B 21,50-32,499 4SMS795

PMX16B 32,50-60,000 5SMS795

.于直径 .10-60,500 mm 通孔的浮动.杆

DC 订购代码 产品型号 尺. mm

OAL LB LS LUX BDX DMM

7,75-9,9 03197751

PMX05T-FL-04100-16N1

102 96 48 41 15 16

9,901-14,499 03002825

PMX06T-FL-05700-16N1

117 110 48 57 15 16

14,5-21,499 03002827

PMX08T-FL-08200-20N1

147 137 50 82 19 20

21,5-32,499 03002829

PMX12T-FL-10400-25N1

32,5-60,5 03002831

PMX16T-FL-12700-32N1

适 .杆 适.直径 (mm) 压板扳.

冷却环

PMX05T 7,750-9,900 1.5SMS795 RT05-KI

. 范围 .杆尺. 订购代码 可换扳.芯 订购代码 扭矩扳. 扭矩值

7,750-9,900 PMX05 03178237

H00-1.5-27

03178196

H00-1505-24

0,5 Nm

.于直径 .10-60,500 mm 盲孔的浮动.杆

DC7,75-9,9 订购代码03271916

产品型号PMX05B-FL-04100-16N1

OAL 102 LB 96 LS 48 LUX 41 BDX 15 DMM 16

9,901-14,499 03002826

PMX06B-FL-05700-16N1

14,5-21,499 03002828

PMX08B-FL-08200-20N1

21,5-32,499 03002830

PMX12B-FL-10400-25N1

32,5-60,5 03002832

PMX16B-FL-12700-32N1

适 .杆PMX05B 适.直径 (mm)7,750-9,900 压板扳. 1.5SMS795 冷却环 RT05-KI

PMX16B 32,50-60,500 5SMS795

.于非标设计直径 .7,75-60,500 mm 通孔和盲孔的.头

.关于切削参数,参见第 266 页 .关于槽型 EB45、EB845 或 EB25 的选择,参见第 247 页

DC7,75-9,999 产品型号PMX5-7.75-XX-XXXX 尺. mm 6 .体规格PMX05-xx 槽型EB45 EB845 EB25 材质等级

LFS 6,0 DMM 4,5 ]H15 ]CP20 ]RX2000 ]CF ]RX1500 ]RN2010 ]RM2020 ]RM2090 ] RS2090

10,0-14,499 PMX5-10.0-XX-XXXX 7,0 6,0 6 PMX06-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

14,5-21,499 PMX5-14.5-XX-XXXX 10,0 8,0 6 PMX08-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

21,5-32,499 PMX5-21.5-XX-XXXX 12,0 12,0 8 PMX12-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

32,5-60,5 PMX5-32.5-XX-XXXX 14,0 16,0 10 PMX16-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

= 非标准库存。供货情况请参照新的价格和库存表注]意:在订购非标 Precimaster Plus 铰刀时,请注明要铰削的孔的直径和公差。订购.例: PMX5-16.515 P7-EB45 RM2020

DC7,75-9,999 产品型号PMX6-7.75-XX-XXXX 尺. mm 6 .体规格PMX05-xx 槽型EB45 EB845 EB25 材质等级

10,0-14,499 PMX6-10.0-XX-XXXX 7,0 6,0 6 PMX06-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

14,5-21,499 PMX6-14.5-XX-XXXX 10,0 8,0 6 PMX08-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

21,5-32,499 PMX6-21.5-XX-XXXX 12,0 12,0 8 PMX12-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

32,5-60,5 PMX6-32.5-XX-XXXX 14,0 16,0 10 PMX16-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

= 非标准库存。供货情况请参照新的价格和库存表注]意:在订购非标 Precimaster Plus 铰刀时,请注明要铰削的孔的直径和公差。订购.例: PMX6-16.515 P7-EB45 RM2020.

.于直径 .10-32,500 mm 通孔和盲孔的可涨式.头

.关于切削参数, 参见第 266 页 .关于槽型 EB45、EB845 或 EB25 的选择,参见第 247 页

DC10,0-14,499 产品型号PMX8-10.0-XX-XXXX 尺. mm 6 .体规格PMX06-xx 槽型EB45 EB845 EB25 材质等级

LFS 7,0 DMM 6,0 ]H15 ]CP20 ]RX2000 ]CF ]RX1500 ]RN2010 ]RM2020 ]RM2090 ] RS2090

14,5-21,499 PMX8-14.5-XX-XXXX 10,0 8,0 6 PMX08-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

21,5-32,499 PMX8-21.5-XX-XXXX 12,0 12,0 8 PMX12-xx EB45 EB845 EB25 ] ] ] ] ] ] ] ] ]

= 非标准库存。供货情况请参照新的价格和库存表注]意:在订购非标 Precimaster Plus 铰刀时,请注明要铰削的孔的直径和公差。订购.例: PMX8-16.515 P7-EB45 RM2020

.需等待报价–交货期短

我们提供 Precimaster Plus 铰刀和刀柄的非标设计。现在,您可以使用山高非标设计软件为您自己的中间直径 . 铰刀和非标 Precimaster Plus 刀杆询价。易于操作:只需标明零件的大、小直径或使用软件中提供的 ISO 公差系统。自动生成 Precimaster Plus 刀头型号。非标设计带给你不少便利:

.无需等待报价!即刻获取价格与交货期! .直接展现您的需求。无偏差。 .交货期短。

问题解决

Precimaster Plus 重磨操作指南

Z=6

Z=8

Z=10

. Precimaster Plus t β1 β2 β3

10,00-14,499 8° 18° 8°

15° 10,00-14,499

8° 18° 8°

0,20 14,500-21,499

0,20 21,500-32,499

0,25 32,500-60,499

8° 15° 8° 0,30

金刚石砂轮颗粒度: D6 – 用于后角 (β1–β3) D64 – 用于第二后角 (β2)

重磨会减小铰刀直径再镀层可能产生过大的直径导向倒角的大跳动量为 10 μm

切削参数 – PM Plus .-EB845

SMG ap (.) f vc

z=6 z=8 z=6 z=8 z=10 H15 CP20 RX2000 CF RX1500

P3 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,30 0,20-0,90 0,30-1,20 0,30-1,50 - 60 (30-100) 80 (30-150) 180 (90-200) 220 (120-300)

P4 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,30 0,20-0,70 0,30-0,90 0,40-1,10 - 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P5 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,30 0,20-0,70 0,30-0,90 0,40-1,10 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P6 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,30 0,20-0,70 0,30-0,90 0,40-1,10 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P7 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,30 0,20-0,70 0,30-0,90 0,40-1,10 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P8 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,30 0,20-0,70 0,30-0,90 0,40-1,10 15 (10-20) 35 (20-60) 40 (20-80) 80 (60-120) 120 (80-180)

P11 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,30 0,20-0,70 0,30-0,90 0,40-1,10 15 (10-20) 35 (20-60) 40 (20-80) 80 (60-120) 120 (80-180)

P12 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,30 0,20-0,70 0,30-0,90 0,40-1,10 12 (8-15) 25 (15-45) 30 (15-65) 65 (45-95) 95 (65-145)

M1 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,10 12 (9-15) 25 (15-40) 35 (20-70) - -

M2 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,10 - 25 (15-40) 35 (20-70) - -

M3 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,10 - 25 (15-40) 35 (20-70) - -

M4 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,10 - 20 (10-30) 25 (15-50) - -

M5 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,10 - 20 (10-30) 25 (15-50) - -

K1 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,25 0,30-0,90 0,30-1,20 0,40-1,50 25 (15-30) 60 (40-100) 80 (30-150) - 220 (120-300)

K2 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,25 0,30-0,90 0,30-1,20 0,40-1,50 25 (20-40) 40 (30-70) - 80 (50-100)

K3 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,25 0,30-0,90 0,30-1,20 0,40-1,50 25 (15-30) 60 (40-100) 80 (30-150) - 220 (120-300)

K4 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,25 0,30-0,90 0,30-1,20 0,40-1,50 25 (15-30) 45 (30-70) 70 (40-120) 100 (70-150) 150 (80-200)

K5 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,25 0,30-0,90 0,30-1,20 0,40-1,50 25 (15-30) 45 (30-70) 70 (40-120) 100 (70-150) 150 (80-200)

K6 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,25 0,30-0,90 0,30-1,20 0,40-1,50 - 60 (40-100) 80 (30-150) - 220 (120-300)

K7 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,10-0,25 0,30-0,90 0,30-1,20 0,40-1,50 - 60 (40-100) 80 (30-150) - 220 (120-300)

S1 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 - 20 (10-25) 20 (10-25) - -

S2 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 - 20 (10-25) 20 (10-25) - -

S3 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 - 20 (10-25) 20 (10-25) - -

S11 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 20 (15-30) 30 (15-40) 40 (20-50) - -

S12 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 20 (15-30) 30 (15-40) 40 (20-50) - -

S13 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 20 (15-30) 30 (15-40) 40 (20-50) - -

H3 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,55 0,40-0,70 - - 10 (8-15) - -

H5 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,55 0,40-0,70 - - 10 (8-15) - -

H7 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,55 0,40-0,70 - - 10 (8-15) - -

H8 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,55 0,40-0,70 - - 10 (8-15) - -

H11 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,55 0,40-0,70 - - 10 (8-15) - -

H12 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,55 0,40-0,70 - - 10 (8-15) - -

H21 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,55 0,40-0,70 - - 10 (8-15) - -

H31 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,55 0,40-0,70 - - 10 (8-15) - -

PM1 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,1-0,30 0,20-0,60 0,30-0,80 0,40-1,00 - 50 (30-80) 70 (40-100) - -

PM2 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,1-0,30 0,20-0,60 0,30-0,80 0,40-1,00 - 50 (30-80) 70 (40-100) - -

PM3 PMX5/PMX6/PMX8-EB845 0,10-0,20 0,1-0,30 0,20-0,60 0,30-0,80 0,40-1,00 - 50 (30-80) 70 (40-100) - -

切削参数 – PM Plus…-EB25

z = 6 z = 8 z = 6 z = 8 z = 10 H15 CP20 RX2000 CF RX1500

P1 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-1,80 1,00-2,40 1,20-3,00 25 (15-30) 60 (30-100) 80 (30-150) 180 (90-200) 220 (120-300)

P2 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-1,80 1,00-2,40 1,20-3,00 25 (15-30) 60 (30-100) 80 (30-150) 180 (90-200) 220 (120-300)

P3 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-1,80 1,00-2,40 1,20-3,00 25 (15-30) 60 (30-100) 80 (30-150) 180 (90-200) 220 (120-300)

P4 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-1,80 1,00-2,40 1,20-3,00 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P5 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-1,80 1,00-2,40 1,20-3,00 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P6 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-1,80 1,00-2,40 1,20-3,00 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P7 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-1,80 1,00-2,40 1,20-3,00 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

M1 PMX5/PMX6/PMX8-EB25 0,08-0,15 0,10-0,20 0,80-1,20 1,00-2,00 1,20-2,50 - 25 (15-40) 35 (20-70) - -

K1 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,25 0,80-2,20 1,00-2,80 1,20-3,50 25 (15-30) 60 (40-100) 80 30-150) - 220 (120-300)

K2 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,25 0,80-1,80 1,00-2,40 1,20-3,00 - 25 (20-40) 40 (30-70) - 80 (50-100)

K3 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,25 0,80-2,20 1,00-2,80 1,20-3,50 25 (15-30) 60 (40-100) 80 (30-150) - 220 (120-300)

K4 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,25 0,80-2,20 1,00-2,80 1,20-3,50 25 (15-30) 45 (30-70) 70 (40-120) 100 (70-150) 150 (80-200)

K5 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,25 0,80-2,20 1,00-2,80 1,20-3,50 25 (15-30) 45 (30-70) 70 (40-120) 100 (70-150) 150 (80-200)

K6 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,25 0,80-1,80 1,00-2,40 1,20-3,00 - 60 (40-100) 80 (30-150) - 220 (120-300)

K7 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,25 0,80-1,80 1,00-2,40 1,20-3,00 - 60 (40-100) 80 (30-150) - 220 (120-300)

N1 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-2,20 1,00-2,80 1,20-3,50 50 (30-100) - - - -

N2 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-2,20 1,00-2,80 1,20-3,50 50 (30-100) - - - -

N3 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-2,20 1,00-2,80 1,20-3,50 50 (30-100) - - - -

N11 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,80-2,20 1,00-2,80 1,20-3,50 50 (30-100) - - - -

PM1 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,50-1,80 0,80-2,00 1,00-2,50 - 50 (30-80) 70 (40-100) - -

PM2 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,50-1,80 0,80-2,00 1,00-2,50 - 50 (30-80) 70 (40-100) - -

PM3 PMX5/PMX6/PMX8-EB25 0,10-0,20 0,10-0,30 0,50-1,80 0,80-2,00 1,00-2,50 - 50 (30-80) 70 (40-100) - -

切削参数 – PM Plus…-EB45

P1 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 25 (15-30) 60 (30-100) 80 (30-150) 180 (90-200) 220 (120-300)

P2 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 25 (15-30) 60 (30-100) 80 (30-150) 180 (90-200) 220 (120-300)

P3 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 25 (15-30) 60 (30-100) 80 (30-150) 180 (90-200) 220 (120-300)

P4 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,20-0,70 0,30-1,00 0,40-1,20 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P5 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,20-0,70 0,30-1,00 0,40-1,20 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P6 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,20-0,70 0,30-1,00 0,40-1,20 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P7 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,20-0,70 0,30-1,00 0,40-1,20 20 (10-25) 50 (30-80) 60 (30-120) 120 (80-150) 180 (90-200)

P8 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,20-0,70 0,30-1,00 0,40-1,20 15 (10-20) 35 (20-60) 40 (20-80) 80 (60-120) 120 (80-180)

P11 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,20-0,70 0,30-1,00 0,40-1,20 15 (10-20) 35 (20-60) 40 (20-80) 80 (60-120) 120 (80-180)

P12 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,20-0,70 0,30-1,00 0,40-1,20 12 (8-15) 25 (15-45) 30 (15-65) 65 (45-95) 95 (65-145)

M1 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,00 12 (9-15) 25 (15-40) 35 (20-70) - -

M2 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,00 - 25 (15-40) 35 (20-70) - -

M3 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,00 - 25 (15-40) 35 (20-70) - -

M4 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,00 - 20 (10-30) 25 (15-50) - -

M5 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,40-1,00 - 20 (10-30) 25 (15-50) - -

K1 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,25 0,30-0,90 0,40-1,20 0,50-1,50 25 (15-30) 60 (40-100) 80 (30-150) - 220 (120-300)

K2 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,25 0,30-0,90 0,40-1,20 0,50-1,50 - 25 (20-40) 40 (30-70) - 80 (50-100)

K3 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,25 0,30-0,90 0,40-1,20 0,50-1,50 25 (15-30) 60 (40-100) 80 (30-150) - 220 (120-300)

K4 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,25 0,30-0,90 0,40-1,20 0,50-1,50 25 (15-30) 45 (30-70) 70 (40-120) 100 (70-150) 150 (80-200)

K5 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,25 0,30-0,90 0,40-1,20 0,50-1,50 25 (15-30) 45 (30-70) 70 (40-120) 100 (70-150) 150 (80-200)

K6 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,25 0,30-0,90 0,40-1,20 0,50-1,50 - 60 (40-100) 80 (30-150) - 220 (120-300)

K7 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,25 0,30-0,90 0,40-1,20 0,50-1,50 - 60 (40-100) 80 (30-150) - 220 (120-300)

N1 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 50 (30-100) - 80 (30-150) - -

N2 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 50 (30-100) - 80 (30-150) - -

N3 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 50 (30-100) - 80 (30-150) - -

N11 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 50 (30-100) - 80 (30-150) - -

S1 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 - 20 (10-25) 20 (10-25) - -

S2 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 - 20 (10-25) 20 (10-25) - -

S3 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 - 20 (10-25) 20 (10-25) - -

S11 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 20 (15-30) 30 (15-40) 40 (20-50) - -

S12 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 20 (15-30) 30 (15-40) 40 (20-50) - -

S13 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,40-1,00 20 (15-30) 30 (15-40) 40 (20-50) - -

H3 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,60 0,40-0,75 - - 10 (8-15) - -

H5 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,60 0,40-0,75 - - 10 (8-15) - -

H7 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,60 0,40-0,75 - - 10 (8-15) - -

H8 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,60 0,40-0,75 - - 10 (8-15) - -

H11 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,60 0,40-0,75 - - 10 (8-15) - -

H12 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,60 0,40-0,75 - - 10 (8-15) - -

H21 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,60 0,40-0,75 - - 10 (8-15) - -

H31 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,40 0,30-0,60 0,40-0,75 - - 10 (8-15) - -

PM1 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 - 50 (30-80) 70 (40-100) - -

PM2 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 - 50 (30-80) 70 (40-100) - -

PM3 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 - 50 (30-80) 70 (40-100) - -

TS1 PMX5/PMX6/PMX8-EB45 0,10-0,15 0,10-0,20 0,30-0,90 0,40-1,20 0,50-1,50 20 (15-25) - 40 (20-60) - -

TS2 PMX5/PMX6/PMX8-EB45 0,10-0,15 0,10-0,20 0,30-0,90 0,40-1,20 0,50-1,50 20 (15-25) - 40 (20-60) - -

TS3 PMX5/PMX6/PMX8-EB45 0,10-0,15 0,10-0,20 0,30-0,90 0,40-1,20 0,50-1,50 20 (15-25) - 40 (20-60) - -

TS4 PMX5/PMX6/PMX8-EB45 0,10-0,15 0,10-0,20 0,30-0,90 0,40-1,20 0,50-1,50 20 (15-25) - 40 (20-60) - -

TP1 PMX5/PMX6/PMX8-EB45 0,10-0,15 0,10-0,20 0,30-0,90 0,40-1,20 0,50-1,50 20 (15-25) - 40 (20-60) - -

TP2 PMX5/PMX6/PMX8-EB45 0,10-0,15 0,10-0,20 0,30-0,90 0,40-1,20 0,50-1,50 20 (15-25) - 40 (20-60) - -

TP3 PMX5/PMX6/PMX8-EB45 0,10-0,15 0,10-0,20 0,30-0,90 0,40-1,20 0,50-1,50 20 (15-25) - 40 (20-60) - -

TP4 PMX5/PMX6/PMX8-EB45 0,10-0,15 0,10-0,20 0,30-0,90 0,40-1,20 0,50-1,50 20 (15-25) - 40 (20-60) - -

GR1 PMX5/PMX6/PMX8-EB45 0,10-0,30 0,10-0,40 0,30-0,90 0,40-1,20 0,50-1,50 40 (80-20) - 60 (30-120) - -

SMG = 山高材料组 ap = mm f = mm/rev vc= m/min所有切削参数均为起始值

z=6 z=8 / z=10 z=6 z=8 z=10 RN2010 RM2020 RM2090 RS2090

M1 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 - 25 (15-40) 40 (25-80) -

M2 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 - 25 (15-40) 40 (25-80) -

M3 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 - 25 (15-40) 40 (25-80) -

M4 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 - 20 (10-30) 30 (20-60) -

M5 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 - 20 (10-30) 30 (20-60) -

N1 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 50 (30-100) - - -

N2 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 50 (30-100) - - -

N3 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 50 (30-100) - - -

N11 PMX5/PMX6/PMX8-EB45 0,10-0,20 0,10-0,30 0,30-0,90 0,40-1,20 0,50-1,50 50 (30-100) - - -

S1 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - - 25 (12-30)

S2 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - - 25 (12-30)

S3 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - - 25 (12-30)

S11 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - - 50 (25-65)

S12 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - - 50 (25-65)

S13 PMX5/PMX6/PMX8-EB45 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - - 50 (25-65)

切削参数 – PM Plus…-EB845

z=6 z=8/ z=10 z=6 z=8 z=10 RM2020 RM2090 RS2090

M1 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 25 (15-40) 35 (20-70) -

M2 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 25 (15-40) 35 (20-70) -

M3 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 25 (15-40) 35 (20-70) -

M4 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 20 (10-30) 25 (15-50) -

M5 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,20 0,20-0,60 0,30-0,80 0,35-1,00 20 (10-30) 25 (15-50) -

S1 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - 25 (12-30)

S2 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - 25 (12-30)

S3 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - 25 (12-30)

S11 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - 50 (25-65)

S12 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - 50 (25-65)

S13 PMX5/PMX6/PMX8-EB845 0,08-0,15 0,10-0,15 0,20-0,60 0,30-0,80 0,35-1,00 - - 50 (25-65)

Nano. x.

Nano. x. . 范围 铰削深度 钻头 .公差 中间直径 表面粗糙度

2,97-12,05 mm 5-12 x D IT 7 是,通过非标设计提供 Ra 0,8–1,2 μm

Nano.x. 是山高的整体硬质合金铰刀系列,专用于加工直径范围为 2.97 至 12.05 mm 的小孔。Nano.x 采用独特的 Quick-Fit 专利夹紧系统,仅需两个刀杆就可夹持整个直径范围。刀杆带有内冷通道,采用一种简单的可调系统,因此出口型式可根据应用场合设为通孔或盲孔。

两种 Quick-.t 规格覆盖所有直径范围

产品型号编码 - 铰.

铰刀类型 孔径与精度 导向槽型 材质等级

产品型号编码 - 中间直径铰.

柄部型式 工作长度 圆柱柄 中置 圆柱柄 DIN 1835

跳动量 旋转式刀具

大推荐跳动量:5 μm。

簧夹头刀柄。

注意:由于采用了冷却液出口调节密封 O 形圈,因此不推荐使用热胀刀柄。

静.式刀具

使用山高浮动刀柄,参见第 359-363 页。

浮动刀柄使铰刀在预钻孔中自对中心。

为获得佳的刀具寿命与孔径,应遵循下列冷却液要求。

推荐使用内冷却。可以使用外冷供应,但切削参数需降低 75%。

矿物油含量少为 40% 的可溶切削油。加工不锈钢时推荐使用纯矿物油。

小浓度为 6–8%。过滤 30–50 μm。对于铰刀直径而言,小流量为 0,5 l/min/mm(例:铰刀直径为 . 10,小流量为 5 l/min)。

Nano.x 铰刀的齿距是不等分的。在测量直径时,确保 2 个刀齿成 180° 夹角。

导向槽型和材质等级 - 应.

.于直径 .2,97-6,00 mm 盲孔和通孔的铰.

DC 孔径 ISO (mm) 孔径 min/max (mm) 孔径 min/max (inch) 钻头直径 (mm) 产品型号 尺. mm 槽型 材质等级

LUX DMM OAL .体规格 EB45 EB845 EB25 RX2000 H15

2,97 2,97 H7 2,970/2,980 .1169/ .1173 2,8-2,9 NF06-2.97 H7-EB . 4 40 6 60 NFQF06… ] ] 02728852

2,98 2,98 H7 2,980/2,990 .1173/ .1177 2,8-2,9 NF06-2.98 H7-EB . 4 40 6 60 NFQF06… ] ] 02728853

2,99 2,99 H7/3 K7 2,990/3,000 .1177/ .1181 2,8-2,9 NF06-2.99 H7-EB . 4 40 6 60 NFQF06… ] ] 02728854

3,00 3 H7 3,000/3,010 .1181/ .1185 2,8-2,9 NF06-3 H7-EB . 4 40 6 60 NFQF06… ] ] 02728858

3,01 3,01 H7 3,010/3,022 .1185/ .1190 2,8-2,9 NF06-3.01 H7-EB . 4 40 6 60 NFQF06… ] ] 02728860

3,02 3,02 H7/3 D7 3,020/3,032 .1189/ .1194 2,9 NF06-3.02 H7-EB . 4 40 6 60 NFQF06… ] ] 02728862

3,03 3,03 H7 3,030/3,042 .1193/ .1198 2,9 NF06-3.03 H7-EB . 4 40 6 60 NFQF06… ] ] 02728864

3,04 3,04 H7/3D10 3,040/3,052 .1197/ .1202 2,9 NF06-3.04 H7-EB . 4 40 6 60 NFQF06… ] ] 02728865

3,05 3,05 H7 3,050/3,062 .1201/ .1206 2,9 NF06-3.05 H7-EB . 4 40 6 60 NFQF06… ] ] 02728866

3,167 3,167 H7 3,167/3,179 .1247/ .1252 3 NF06-3.167 H7-EB . 4 60 6 80 NFQF06… ] ] 02761485

3,175 3,175 H7 3,187/3,175 .1255/ .1250 3 NF06-3.175 H7-EB . 4 60 6 80 NFQF06 . ] ] 02761489

3,49 3,49 H7 3,490/3,502 .1374/ .1379 3,3-3,4 NF06-3.49 H7-EB . 4 60 6 80 NFQF06… ] ] 02728867

3,50 3,5 H7 3,500/3,512 .1378/ .1383 3,3-3,4 NF06-3.5 H7-EB . 4 60 6 80 NFQF06… ] ] 02728868

3,51 3,51 H7 3,510/3,522 .1382/ .1387 3,3-3,4 NF06-3.51 H7-EB . 4 60 6 80 NFQF06… ] ] 02728869

3,52 3,52 H7 3,520/3,532 .1386/ .1391 3,3-3,4 NF06-3.52 H7-EB . 4 60 6 80 NFQF06… ] ] 02728870

3,97 3,97 H7 3,970/3,982 .1563/ .1568 3,8-3,9 NF06-3.97 H7-EB . 4 60 6 80 NFQF06… ] ] 02728871

3,98 3,98 H7/4 P7 3,980/3,992 .1567/ .1572 3,8-3,9 NF06-3.98 H7-EB . 4 60 6 80 NFQF06… ] ] 02728872

3,99 3,99 H7/4 K8 3,990/4,002 .1571/ .1576 3,8-3,9 NF06-3.99 H7-EB . 4 60 6 80 NFQF06… ] ] 02728873

4,00 4 H7 4,000/4,012 .1575/ .1580 3,8-3,9 NF06-4 H7-EB . 4 60 6 80 NFQF06… ] ] 02728874

4,01 4,01 H7/4 F7 4,010/4,022 .1579/ .1583 3,8-3,9 NF06-4.01 H7-EB . 4 60 6 80 NFQF06… ] ] 02728875

4,02 4,02 H7/4 E7 4,020/4,032 .1583/ .1587 3,9 NF06-4.02 H7-EB . 4 60 6 80 NFQF06… ] ] 02728876

4,03 4,03 H7/4 D7 4,030/4,042 .1587/ .1591 3,9 NF06-4.03 H7-EB . 4 60 6 80 NFQF06… ] ] 02728877

4,04 4,04 H7 4,040/4,052 .1591/ .1595 3,9 NF06-4.04 H7-EB . 4 60 6 80 NFQF06… ] ] 02728879

4,05 4,05 H7 4,050/4,062 .1594/ .1599 3,9 NF06-4.05 H7-EB . 4 60 6 80 NFQF06… ] ] 02728880

4,50 4,5 H7 4,500/4,512 .1772/ .1776 4,3-4,4 NF06-4.5 H7-EB . 4 60 6 80 NFQF06… ] ] 02728881

4,75 4,75 H7 4,762/4,750 .1875/ .1870 4,5 NF06-4.750 H7-EB . 4 60 6 80 NFQF06 . ] ] 02761490

4,762 4,762 H7 4,774/4,762 .1880/ .1875 4,5 NF06-4.762 H7-EB . 4 60 6 80 NFQF06 . ] ] 02761494

4,97 4,97 H7 4,970/4,982 .1957/ .1961 4,8-4,9 NF06-4.97 H7-EB . 4 60 6 80 NFQF06… ] ] 02728882

4,98 4,98 H7/5 P7 4,980/4,992 .1961/ .1965 4,8-4,9 NF06-4.98 H7-EB . 4 60 6 80 NFQF06… ] ] 02728883

4,99 4,99 H7/5 K8 4,990/5,002 .1965/ .1969 4,8-4,9 NF06-4.99 H7-EB . 4 60 6 80 NFQF06… ] ] 02728884

5,00 5 H7 5,000/5,012 .1969/ .1973 4,8-4,9 NF06-5 H7-EB . 4 60 6 80 NFQF06… ] ] 02728927

5,01 5,01 H7/5 F7 5,010/5,022 .1972/ .1977 4,8-4,9 NF06-5.01 H7-EB . 4 60 6 80 NFQF06… ] ] 02728928

5,02 5,02 H7/5 E7 5,020/5,032 .1976/ .1981 4,9 NF06-5.02 H7-EB . 4 60 6 80 NFQF06… ] ] 02728929

5,03 5,03 H7/5 D7 5,030/5,042 .1980/ .1985 4,9 NF06-5.03 H7-EB . 4 60 6 80 NFQF06… ] ] 02728930

5,04 5,04 H7 5,040/5,052 .1984/ .1989 4,9 NF06-5.04 H7-EB . 4 60 6 80 NFQF06… ] ] 02728931

5,05 5,05 H7 5,050/5,062 .1988/ .1993 4,9 NF06-5.05 H7-EB . 4 60 6 80 NFQF06… ] ] 02728932

5,50 5,5 H7 5,500/5,512 .2165/ .2170 5,3-5,4 NF06-5.5 H7-EB . 4 60 6 80 NFQF06… ] ] 02728933

5,97 5,97 H7 5,970/5,982 .2350/ .2355 5,8-5,9 NF06-5.97 H7-EB . 4 60 6 80 NFQF06… ] ] 02728934

5,98 5,98 H7/6 P7 5,980/5,992 .2354/ .2359 5,8-5,9 NF06-5.98 H7-EB . 4 60 6 80 NFQF06… ] ] 02728935

5,99 5,99 H7/6 K8 5,990/6,002 .2358/ .2363 5,8-5,9 NF06-5.99 H7-EB . 4 60 6 80 NFQF06… ] ] 02728936

6,00 6 H7 6,000/6,012 .2362/ .2367 5,8-5,9 NF06-6 H7-EB . 4 60 6 80 NFQF06… ] ] 02728937

标准库存 ]非标准库存。供货情况请参阅新的价格和库存表。注[意:在订购用于中间直径的 Nano.x 铰刀时,请注明要铰削的孔的直径和公差。订购.例: NF10-10,187/10,213-EB845, RX2000

.于直径 .6,01-9,512 mm 盲孔和通孔的铰.

6,01 6,01 H7/6 F7 6,010/6,025 .2366/ .2372 5,8-5,9 NF06-6.01 H7-EB . 4 60 6 80 NFQF06… ] ] 02728938

6,02 6,02 H7/6 E7 6,020/6,035 .2370/ .2376 5,9 NF06-6.02 H7-EB . 4 60 6 80 NFQF06… ] ] 02728939

6,03 6,03 H7/6 D7 6,030/6,045 .2374/ .2380 5,9 NF06-6.03 H7-EB . 4 60 6 80 NFQF06… ] ] 02728940

6,04 6,04 H7 6,040/6,055 .2378/ .2384 5,9 NF06-6.04 H7-EB . 4 60 6 80 NFQF06… ] ] 02728941

6,05 6,05 H7 6,050/6,065 .2382/ .2388 5,9 NF06-6.05 H7-EB . 4 60 6 80 NFQF06… ] ] 02728942

6,334 6,334 H7 6,334/6,349 .2494/ .2500 6,1-6,2 NF10-6.334 H7-EB . 6 83 10 115 NFQF10 . ] ] 02761987

6,35 6,35 H7 6,35/6,365 .2500/ .2506 6,2 NF10-6.350 H7-EB . 6 83 10 115 NFQF10 . ] ] 02762016

6,375 6,375 H7 6,375/6,39 .2510/ .2516 6,2 NF10-6.375 H7-EB . 6 83 10 115 NFQF10 . ] ] 02762017

6,50 6,5 H7 6,500/6,515 .2559/ .2565 6,3-6,35-6,4 NF10-6.5 H7-EB . 6 83 10 115 NFQF10… ] ] 02728943

6,97 6,97 H7 6,970/6,985 .2744/ .2750 6,8-6,9 NF10-6.97 H7-EB . 6 83 10 115 NFQF10… ] ] 02728946

6,98 6,98 H7 6,980/6,995 .2748/ .2754 6,8-6,9 NF10-6.98 H7-EB . 6 83 10 115 NFQF10… ] ] 02728947

6,99 6,99 H7/7 K7 6,990/7,005 .2752/ .2758 6,8-6,9 NF10-6.99 H7-EB . 6 83 10 115 NFQF10… ] ] 02728948

7,00 7 H7 7,000/7,015 .2756/ .2762 6,8-6,9 NF10-7 H7-EB . 6 83 10 115 NFQF10… ] ] 02728949

7,01 7,01 H7 7,010/7,025 .2760/ .2766 6,8-6,9 NF10-7.01 H7-EB . 6 83 10 115 NFQF10… ] ] 02728950

7,02 7,02 H7 7,020/7,035 .2764/ .2770 6,9 NF10-7.02 H7-EB . 6 83 10 115 NFQF10… ] ] 02728951

7,03 7,03 H7/7 E8 7,030/7,045 .2768/ .2774 6,9 NF10-7.03 H7-EB . 6 83 10 115 NFQF10… ] ] 02728952

7,04 7,04 H7/7 D7 7,040/7,055 .2772/ .2778 6,9 NF10-7.04 H7-EB . 6 83 10 115 NFQF10… ] ] 02728953

7,05 7,05 H7 7,050/7,065 .2776/ .2781 6,9 NF10-7.05 H7-EB . 6 83 10 115 NFQF10… ] ] 02728954

7,50 7,5 H7 7,500/7,515 .2953/ .2959 7,3-7,4 NF10-7.5 H7-EB . 6 83 10 115 NFQF10… ] ] 02728955

7,937 7,937 H7 7,937/7,952 .3125/ .3131 7,8 NF10-7.9375 H7-EB . 6 83 10 115 NFQF10 . ] ] 02762018

7,97 7,97 H7 7,970/7,985 .3138/ .3144 7,8-7,9 NF10-7.97 H7-EB . 6 83 10 115 NFQF10… ] ] 02728956

7,98 7,98 H7 7,980/7,995 .3142/ .3148 7,8-7,9 NF10-7.98 H7-EB . 6 83 10 115 NFQF10… ] ] 02728957

7,99 7,99 H7/8 K7 7,990/8,005 .3146/ .3152 7,8-7,9 NF10-7.99 H7-EB . 6 83 10 115 NFQF10… ] ] 02728958

8,00 8 H7 8,000/8,015 .3150/ .3156 7,8-7,9 NF10-8 H7-EB . 6 83 10 115 NFQF10… ] ] 02728959

8,01 8,01 H7 8,010/8,025 .3154/ .3159 7,8-7,9 NF10-8.01 H7-EB . 6 83 10 115 NFQF10… ] ] 02728960

8,02 8,02 H7 8,020/8,035 .3157/ .3163 7,9 NF10-8.02 H7-EB . 6 83 10 115 NFQF10… ] ] 02728961

8,03 8,03 H7/8 E8 8,030/8,045 .3161/ .3167 7,9 NF10-8.03H7-EB .

6 83 10 115 NFQF10… ] ] 02728962

8,04 8,04 H7/8 D7 8,040/8,055 .3165/ .3171 7,9 NF10-8.04 H7-EB . 6 83 10 115 NFQF10… ] ] 02728963

8,05 8,05 H7 8,050/8,065 .3169/ .3175 7,9 NF10-8.05 H7-EB . 6 83 10 115 NFQF10… ] ] 02728964

8,50 8,5 H7 8,500/8,515 .3346/ .3352 8,3-8,338-8,4 NF10-8.5 H7-EB . 6 93 10 125 NFQF10… ] ] 02728965

8,97 8,97 H7 8,970/8,985 .3531/ .3537 8,8-8,9 NF10-8.97 H7-EB . 6 93 10 125 NFQF10… ] ] 02728966

8,98 8,98 H7 8,980/8,995 .3535/ .3541 8,8-8,9 NF10-8.98 H7-EB . 6 93 10 125 NFQF10… ] ] 02728967

8,99 8,99 H7/9 K7 8,990/9,005 .3539/ .3545 8,8-8,9 NF10-8.99 H7-EB . 6 93 10 125 NFQF10… ] ] 02728968

9,00 9 H7 9,000/9,015 .3543/ .3549 8,8-8,9 NF10-9 H7-EB . 6 93 10 125 NFQF10… ] ] 02728974

9,01 9,01 H7 9,010/9,025 .3547/ .3553 8,8-8,9 NF10-9.01 H7-EB . 6 93 10 125 NFQF10… ] ] 02728975

9,02 9,02 H7 9,020/9,035 .3551/ .3557 8,9 NF10-9.02 H7-EB . 6 93 10 125 NFQF10… ] ] 02728976

9,03 9,03 H7/9 E8 9,030/9,045 .3555/ .3561 8,9 NF10-9.03 H7-EB . 6 93 10 125 NFQF10… ] ] 02728977

9,04 9,04 H7/9 D7 9,040/9,055 .3559/ .3565 8,9 NF10-9.04 H7-EB . 6 93 10 125 NFQF10… ] ] 02728978

9,05 9,05 H7 9,050/9,065 .3563/ .3569 8.9 NF10-9.05 H7-EB . 6 93 10 125 NFQF10… ] ] 02728979

9,50 9,5 H7 9,500/9,515 .3740/ .3746 9,3-9,4 NF10-9.5 H7-EB . 6 93 10 125 NFQF10… ] ] 02728980

9,512 9,512 H7 9,512/9,527 .3745/ .3751 9,3-9,4 NF10-9.5123 H7-EB . 6 93 10 125 NFQF10 . ] ] 02762019

.于直径 .9,525-12,05 mm 盲孔和通孔的铰.

DC9,525 孔径 ISO (mm)9,525 H7 孔径 min/max (mm)9,525/9,54 孔径 min/max (inch) .3750/ .3756 钻头直径 (mm)9,8-9,9 产品型号NF10-9.525 H7-EB . 尺. mm 槽型 材质等级

6 LUX 93 DMM 10 OAL125 .体规格 NFQF10 . [EB45 ]EB845 ]EB25 02762020

RX2000 ] H15

9,97 9,97 H7 9,970/9,985 .3925/ .3931 9,8-9,9 NF10-9.97 H7-EB . 6 93 10 125 NFQF10… ] ] 02728981

9,98 9,98 H7 9,980/9,995 .3929/ .3935 9,8-9,9 NF10-9.98 H7-EB . 6 93 10 125 NFQF10… ] ] 02728982

9,99 9,99 H7/10 K7 9,990/10,005 .3933/ .3939 9,8-9,9 NF10-9.99 H7-EB . 6 93 10 125 NFQF10… ] ] 02728983

10,00 10 H7 10,000/10,015 .3937/ .3943 9,8-9,9 NF10-10 H7-EB . 6 93 10 125 NFQF10… ] ] 02728986

10,01 10,01 H7 10,010/10,028 .3941/ .3948 9,8-9,9 NF10-10.01 H7-EB . 6 93 10 125 NFQF10… ] ] 02728987

10,02 10,02 H7 10,020/10,038 .3945/ .3952 9,8-9,9 NF10-10.02 H7-EB . 6 93 10 125 NFQF10… ] ] 02728988

10,03 10,03 H7/10 E8 10,030/10,048 .3949/ .3956 9,9 NF10-10.03 H7-EB . 6 93 10 125 NFQF10… ] ] 02728989

10,04 10,04 H7/10 D7 10,040/10,058 .3953/ .3960 9,9 NF10-10.04 H7-EB . 6 93 10 125 NFQF10… ] ] 02728990

10,05 10,05 H7 10,050/10,068 .3957/ .3964 9,9 NF10-10.05 H7-EB . 6 93 10 125 NFQF10… ] ] 02728991

10,50 10,5 H7 10,500/10,518 .4134/ .4141 10,319-10,4 NF10-10.5 H7-EB . 6 114 10 145 NFQF10… ] ] 02728992

10,97 10,97 H7 10,970/10,988 .4319/ .4326 10,8 NF10-10.97 H7-EB . 6 114 10 145 NFQF10… ] ] 02728994

10,98 10,98 H7 10,980/10,998 .4323/ .4330 10,8 NF10-10.98 H7-EB . 6 114 10 145 NFQF10… ] ] 02728995

10,99 10,99 H7 10,990/11,008 .4327/ .4334 10,8 NF10-10.99 H7-EB . 6 114 10 145 NFQF10… ] ] 02728996

11,00 11 H7 11,000/11,018 .4331/ .4338 10,8 NF10-11 H7-EB . 6 114 10 145 NFQF10… ] ] 02728997

11,01 11,01 H7 11,010/11,028 .4335/ .4342 10,8 NF10-11.01 H7-EB . 6 114 10 145 NFQF10… ] ] 02728998

11,02 11,02 H7/11 F8 11,020/11,038 .4339/ .4346 10,8 NF10-11.02 H7-EB . 6 114 10 145 NFQF10… ] ] 02729001

11,03 11,03 H7 11,030/11,048 .4343/ .4350 10,8 NF10-11.03 H7-EB . 6 114 10 145 NFQF10… ] ] 02729003

11,04 11,04 H7/11 E7 11,040/11,058 .4346/ .4354 10,8 NF10-11.04 H7-EB . 6 114 10 145 NFQF10… ] ] 02729004

11,05 11,05 H7/11 D7 11,050/11,068 .4350/ .4357 10,8 NF10-11.05 H7-EB . 6 114 10 145 NFQF10… ] ] 02729005

11,112 11,112 H7 11,112/11,130 .4375/ .4382 10,9-11 NF10-11.112 H7-EB . 6 114 10 145 NFQF10 . ] ] 02762021

11,50 11,5 H7 11,500/11,518 .4528/ .4535 11,3 NF10-11.5 H7-EB . 6 114 10 145 NFQF10… ] ] 02729007

11,97 11,97 H7 11,970/11,988 .4713/ .4720 11,8 NF10-11.97 H7-EB . 6 114 10 145 NFQF10… ] ] 02729008

11,98 11,98 H7 11,980/11,998 .4717/ .4724 11,8 NF10-11.98 H7-EB . 6 114 10 145 NFQF10… ] ] 02729009

11,99 11,99 H7 11,990/12,008 .4720/ .4728 11,8 NF10-11.99 H7-EB . 6 114 10 145 NFQF10… ] ] 02729010

12,00 12 H7 12,000/12,018 .4724/ .4731 11,8 NF10-12 H7-EB . 6 114 10 145 NFQF10… ] ] 02729011

12,01 12,01 H7 12,010/12,028 .4728/ .4735 11,8 NF10-12.01 H7-EB . 6 114 10 145 NFQF10… ] ] 02729012

12,02 12,02 H7/12 F8 12,020/12,038 .4732/ .4739 11,8-11,906 NF10-12.02 H7-EB . 6 114 10 145 NFQF10… ] ] 02729013

12,03 12,03 H7 12,030/12,048 .4736/ .4743 11,8-11,906 NF10-12.03 H7-EB . 6 114 10 145 NFQF10… ] ] 02729014

12,04 12,04 H7/12 E7 12,040/12,058 .4740/ .4747 11,8-11,906 NF10-12.04 H7-EB . 6 114 10 145 NFQF10… ] ] 02729015

12,05 12,05 H7/12 D7 12,050/12,068 .4744/ .4751 11,8-11,906 NF10-12.05 H7-EB . 6 114 10 145 NFQF10… ] ] 02729016

中间直径

.关于切削参数,参见第 285 页 .关于导向槽型 EB45 或 EB845 的选择,参见第 247 页

DC2,97-3,05 产品型号NF06-2.970-XX-XXXX 尺. mm 4 .体规格NFQF06-xx 槽型EB45 EB845 材质等级

OAL 60,0 LUX 40,0 DMM 6,0 ]H15 ]RX2000 ]RN2010 ]RM2020 ]RM2090 ] RS2090

3,051-6,05 NF06-3.051-XX-XXXX 80,0 60,0 6,0 4 NFQF06-xx EB45 EB845 ] ] ] ] ] ]

6,051-8,05 NF10-6.051-XX-XXXX 115,0 83,0 10,0 6 NFQF10-xx EB45 EB845 ] ] ] ] ] ]

8,051-10,05 NF10-8.051-XX-XXXX 125,0 93,0 10,0 6 NFQF10-xx EB45 EB845 ] ] ] ] ] ]

10,051-12,05 NF10-10.051-XX-XXXX 145,0 114,0 10,0 6 NFQF10-xx EB45 EB845 ] ] ] ] ] ]

= 非标准库存。供货情况请参照新的价格和库存表注]意:在订购非标 Nano.x 铰刀时,请注明要铰削的孔的直径和公差。订购.例: NF10-10,187/10,213-EB845, RS2090

.于直径 .2,97-6,00 mm 盲孔和通孔的铰. - 短型

.关于材质和槽型,参见第 272-273 页

DC2,97 孔径 min / max (mm)2,97 / 2,98 孔径 min/max (inch) .1169/ .1173 产品型号NS06-2.97H7-EB . 尺. mm

4 LUX 25,0 DMM 6,0 OAL45,0 .体规格 NFQF06 .

2,98 2,98 / 2,99 .1173/ .1177 NS06-2.98H7-EB . 4 25,0 6,0 45,0 NFQF06 .

2,99 2,99 / 3,0 .1177/ .1181 NS06-2.99H7-EB . 4 25,0 6,0 45,0 NFQF06 .

3,0 3,0 / 3,01 .1181/ .1185 NS06-3.00H7-EB . 4 25,0 6,0 45,0 NFQF06 .

3,01 3,01 / 3,022 .1185/ .1190 NS06-3.01H7-EB . 4 25,0 6,0 45,0 NFQF06 .

3,02 3,02 / 3,032 .1189/ .1194 NS06-3.02H7-EB . 4 25,0 6,0 45,0 NFQF06 .

3,03 3,03 / 3,042 .1193/ .1198 NS06-3.03H7-EB . 4 25,0 6,0 45,0 NFQF06 .

3,04 3,04 / 3,052 .1197/ .1202 NS06-3.04H7-EB . 4 25,0 6,0 45,0 NFQF06 .

3,05 3,05 / 3,062 .1201/ .1206 NS06-3.05H7-EB . 4 25,0 6,0 45,0 NFQF06 .

3,167 3,167 / 3,167 .1247/ .1247 NS06-3.167H7-EB . 4 30,0 6,0 50,0 NFQF06 .

3,175 3,175 / 3,187 .1250/ .1255 NS06-3.175H7-EB . 4 30,0 6,0 50,0 NFQF06 .

3,49 3,49 / 3,502 .1374/ .1379 NS06-3.49H7-EB . 4 30,0 6,0 50,0 NFQF06 .

3,5 3,5 / 3,512 .1378/ .1383 NS06-3.50H7-EB . 4 30,0 6,0 50,0 NFQF06 .

3,51 3,51 / 3,522 .1382/ .1387 NS06-3.51H7-EB . 4 30,0 6,0 50,0 NFQF06 .

3,52 3,52 / 3,532 .1386/ .1391 NS06-3.52H7-EB . 4 30,0 6,0 50,0 NFQF06 .

3,97 3,97 / 3,982 .1563/ .1568 NS06-3.97H7-EB . 4 30,0 6,0 50,0 NFQF06 .

3,98 3,98 / 3,992 .1567/ .1572 NS06-3.98H7-EB . 4 30,0 6,0 50,0 NFQF06 .

3,99 3,99 / 4,002 .1571/ .1576 NS06-3.99H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,0 4,0 / 4,012 .1575/ .1580 NS06-4.00H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,01 4,01 / 4,022 .1579/ .1583 NS06-4.01H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,02 4,02 / 4,032 .1583/ .1587 NS06-4.02H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,03 4,03 / 4,042 .1587/ .1591 NS06-4.03H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,04 4,04 / 4,052 .1591/ .1595 NS06-4.04H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,05 4,05 / 4,062 .1594/ .1599 NS06-4.05H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,5 4,5 / 4,512 .1772/ .1776 NS06-4.50H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,75 4,75 / 4,762 .1870/ .1875 NS06-4.750H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,762 4,762 / 4,774 .1875/ .1880 NS06-4.762H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,97 4,97 / 4,982 .1957/ .1961 NS06-4.97H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,98 4,98 / 4,992 .1961/ .1965 NS06-4.98H7-EB . 4 30,0 6,0 50,0 NFQF06 .

4,99 4,99 / 5,002 .1965/ .1969 NS06-4.99H7-EB . 4 30,0 6,0 50,0 NFQF06 .

5,0 5,0 / 5,012 .1969/ .1973 NS06-5.00H7-EB . 4 30,0 6,0 50,0 NFQF06 .

5,01 5,01 / 5,022 .1972/ .1977 NS06-5.01H7-EB . 4 30,0 6,0 50,0 NFQF06 .

5,02 5,02 / 5,032 .1976/ .1981 NS06-5.02H7-EB . 4 30,0 6,0 50,0 NFQF06 .

5,03 5,03 / 5,042 .1980/ .1985 NS06-5.03H7-EB . 4 30,0 6,0 50,0 NFQF06 .

5,04 5,04 / 5,052 .1984/ .1989 NS06-5.04H7-EB . 4 30,0 6,0 50,0 NFQF06 .

5,05 5,05 / 5,062 .1988/ .1993 NS06-5.05H7-EB . 4 30,0 6,0 50,0 NFQF06 .

5,5 5,5 / 5,512 .2165/ .2170 NS06-5.50H7-EB . 4 30,0 6,0 50,0 NFQF06 .

5,97 5,97 / 5,982 .2350/ .2355 NS06-5.97H7-EB . 4 31,0 6,0 50,0 NFQF06 .

5,98 5,98 / 5,992 .2354/ .2359 NS06-5.98H7-EB . 4 31,0 6,0 50,0 NFQF06 .

5,99 5,99 / 6,002 .2358/ .2363 NS06-5.99H7-EB . 4 31,0 6,0 50,0 NFQF06 .

6,0 6,0 / 6,012 .2362/ .2367 NS06-6.00H7-EB . 4 31,0 6,0 50,0 NFQF06 .

注意:在订购用于中间直径的 Nano.x 铰刀时,请注明要铰削的孔的直径和公差。订购.例: NS10-10,187/10,213-EB845, RX2000

.于直径 .6,01-9,512 mm 盲孔和通孔的铰. - 短型

DC6,01 孔径 min / max (mm)6,01 / 6,025 孔径 min/max (inch) .2366/ .2372 产品型号NS06-6.01H7-EB . 尺. mm

4 LUX 31,0 DMM 6,0 OAL50,0 .体规格 NFQF06 .

6,02 6,02 / 6,035 .2370/ .2376 NS06-6.02H7-EB . 4 31,0 6,0 50,0 NFQF06 .

6,03 6,03 / 6,045 .2374/ .2380 NS06-6.03H7-EB . 4 31,0 6,0 50,0 NFQF06 .

6,04 6,04 / 6,055 .2378/ .2384 NS06-6.04H7-EB . 4 31,0 6,0 50,0 NFQF06 .

6,05 6,05 / 6,065 .2382/ .2388 NS06-6.05H7-EB . 4 31,0 6,0 50,0 NFQF06 .

6,334 6,334 / 6,349 .2494/ .2500 NS10-6.334H7-EB . 6 46,0 10,0 78,0 NFQF10

6,35 6,35 / 6,365 .2500/ .2506 NS10-6.350H7-EB . 6 46,0 10,0 78,0 NFQF10

6,375 6,375 / 6,39 .2510/ .2516 NS10-6.375H7-EB . 6 46,0 10,0 78,0 NFQF10

6,5 6,5 / 6,515 .2559/ .2565 NS10-6.5H7-EB . 6 46,0 10,0 78,0 NFQF10

6,97 6,97 / 6,985 .2744/ .2750 NS10-6.97H7-EB . 6 46,0 10,0 78,0 NFQF10

6,98 6,98 / 6,995 .2748/ .2754 NS10-6.98H7-EB . 6 46,0 10,0 78,0 NFQF10

6,99 6,99 / 7,005 .2752/ .2758 NS10-6.99H7-EB . 6 46,0 10,0 78,0 NFQF10

7,0 7,0 / 7,015 .2756/ .2762 NS10-7.00H7-EB . 6 46,0 10,0 78,0 NFQF10

7,01 7,01 / 7,025 .2760/ .2766 NS10-7.01H7-EB . 6 46,0 10,0 78,0 NFQF10

7,02 7,02 / 7,035 .2764/ .2770 NS10-7.02H7-EB . 6 46,0 10,0 78,0 NFQF10

7,03 7,03 / 7,045 .2768/ .2774 NS10-7.03H7-EB . 6 46,0 10,0 78,0 NFQF10

7,04 7,04 / 7,055 .2772/ .2778 NS10-7.04H7-EB . 6 46,0 10,0 78,0 NFQF10

7,05 7,05 / 7,065 .2776/ .2781 NS10-7.05H7-EB . 6 46,0 10,0 78,0 NFQF10

7,5 7,5 / 7,515 .2953/ .2959 NS10-7.50H7-EB . 6 46,0 10,0 78,0 NFQF10

7,9375 7,9375 / 7,952 .3125/ .3131 NS10-7.9375H7-EB . 6 46,0 10,0 78,0 NFQF10

7,97 7,97 / 7,985 .3138/ .3144 NS10-7.97H7-EB . 6 46,0 10,0 78,0 NFQF10

7,98 7,98 / 7,995 .3142/ .3148 NS10-7.98H7-EB . 6 46,0 10,0 78,0 NFQF10

7,99 7,99 / 8,005 .3146/ .3152 NS10-7.99H7-EB . 6 46,0 10,0 78,0 NFQF10

8,0 8,0 / 8,015 .3150/ .3156 NS10-8.00H7-EB . 6 46,0 10,0 78,0 NFQF10

8,01 8,01 / 8,025 .3154/ .3159 NS10-8.01H7-EB . 6 46,0 10,0 78,0 NFQF10

8,02 8,02 / 8,035 .3157/ .3163 NS10-8.02H7-EB . 6 46,0 10,0 78,0 NFQF10

8,03 8,03 / 8,045 .3161/ .3167 NS10-8.03H7-EB . 6 46,0 10,0 78,0 NFQF10

8,04 8,04 / 8,055 .3165/ .3171 NS10-8.04H7-EB . 6 46,0 10,0 78,0 NFQF10

8,05 8,05 / 8,065 .3169/ .3175 NS10-8.05H7-EB . 6 46,0 10,0 78,0 NFQF10

8,5 8,5 / 8,515 .3346/ .3352 NS10-8.50H7-EB . 6 46,0 10,0 78,0 NFQF10

8,97 8,97 / 8,985 .3531/ .3537 NS10-8.97H7-EB . 6 46,0 10,0 78,0 NFQF10

8,98 8,98 / 8,995 .3535/ .3541 NS10-8.98H7-EB . 6 46,0 10,0 78,0 NFQF10

8,99 8,99 / 9,005 .3539/ .3545 NS10-8.99H7-EB . 6 46,0 10,0 78,0 NFQF10

9,0 9,0 / 9,015 .3543/ .3549 NS10-9.00H7-EB . 6 46,0 10,0 78,0 NFQF10

9,01 9,01 / 9,025 .3547/ .3553 NS10-9.01H7-EB . 6 46,0 10,0 78,0 NFQF10

9,02 9,02 / 9,035 .3551/ .3557 NS10-9.02H7-EB . 6 46,0 10,0 78,0 NFQF10

9,03 9,03 / 9,045 .3555/ .3561 NS10-9.03H7-EB . 6 46,0 10,0 78,0 NFQF10

9,04 9,04 / 9,055 .3559/ .3565 NS10-9.04H7-EB . 6 46,0 10,0 78,0 NFQF10

9,05 9,05 / 9,065 .3563/ .3569 NS10-9.05H7-EB . 6 46,0 10,0 78,0 NFQF10

9,5 9,5 / 9,515 .3740/ .3746 NS10-9.50H7-EB . 6 46,0 10,0 78,0 NFQF10

9,5123 9,5123 / 9,527 .3745/ .3751 NS10-9.5123H7-EB . 6 46,0 10,0 78,0 NFQF10

.于直径 .9,525-12,05 mm 盲孔和通孔的铰. - 短型

DC9,525 孔径 min / max (mm)9,525 / 9,54 孔径 min/max (inch) .3750/ .3756 产品型号NS10-9.5250H7-EB . 尺. mm

6 LUX 46,0 DMM 10,0 OAL78,0 .体规格 NFQF10

9,97 9,97 / 9,985 .3925/ .3931 NS10-9.97H7-EB . 6 46,0 10,0 78,0 NFQF10

9,98 9,98 / 9,995 .3929/ .3935 NS10-9.98H7-EB . 6 46,0 10,0 78,0 NFQF10

9,99 9,99 / 10,005 .3933/ .3939 NS10-9.99H7-EB . 6 46,0 10,0 78,0 NFQF10

10,0 10,0 / 10,015 .3937/ .3943 NS10-10.00H7-EB . 6 46,0 10,0 78,0 NFQF10

10,01 10,01 / 10,028 .3941/ .3948 NS10-10.01H7-EB . 6 46,0 10,0 78,0 NFQF10

10,02 10,02 / 10,038 .3945/ .3952 NS10-10.02H7-EB . 6 46,0 10,0 78,0 NFQF10

10,03 10,03 / 10,048 .3949/ .3956 NS10-10.03H7-EB . 6 46,0 10,0 78,0 NFQF10

10,04 10,04 / 10,058 .3953/ .3960 NS10-10.04H7-EB . 6 46,0 10,0 78,0 NFQF10

10,05 10,05 / 10,068 .3957/ .3964 NS10-10.05H7-EB . 6 46,0 10,0 78,0 NFQF10

10,5 10,5 / 10,518 .4134/ .4141 NS10-10.50H7-EB . 6 57,0 10,0 88,0 NFQF10

10,97 10,97 / 10,988 .4319/ .4326 NS10-10.97H7-EB . 6 57,0 10,0 88,0 NFQF10

10,98 10,98 / 10,998 .4323/ .4330 NS10-10.98H7-EB . 6 57,0 10,0 88,0 NFQF10

10,99 10,99 / 11,008 .4327/ .4334 NS10-10.99H7-EB . 6 57,0 10,0 88,0 NFQF10

11,0 11,0 / 11,018 .4331/ .4338 NS10-11.00H7-EB . 6 57,0 10,0 88,0 NFQF10

11,01 11,01 / 11,028 .4335/ .4342 NS10-11.01H7-EB . 6 57,0 10,0 88,0 NFQF10

11,02 11,02 / 11,038 .4339/ .4346 NS10-11.02H7-EB . 6 57,0 10,0 88,0 NFQF10

11,03 11,03 / 11,048 .4343/ .4350 NS10-11.03H7-EB . 6 57,0 10,0 88,0 NFQF10

11,04 11,04 / 11,058 .4346/ .4354 NS10-11.04H7-EB . 6 57,0 10,0 88,0 NFQF10

11,05 11,05 / 11,068 .4350/ .4357 NS10-11.05H7-EB . 6 57,0 10,0 88,0 NFQF10

11,112 11,112 / 11,13 .4375/ .4382 NS10-11.112H7-EB . 6 57,0 10,0 88,0 NFQF10

11,5 11,5 / 11,518 .4528/ .4535 NS10-11.50H7-EB . 6 57,0 10,0 88,0 NFQF10

11,97 11,97 / 11,988 .4713/ .4720 NS10-11.97H7-EB . 6 57,0 10,0 88,0 NFQF10

11,98 11,98 / 11,998 .4717/ .4724 NS10-11.98H7-EB . 6 57,0 10,0 88,0 NFQF10

11,99 11,99 / 12,008 .4720/ .4728 NS10-11.99H7-EB . 6 57,0 10,0 88,0 NFQF10

12,0 12,0 / 12,018 .4724/ .4731 NS10-12.00H7-EB . 6 57,0 10,0 88,0 NFQF10

12,01 12,01 / 12,028 .4728/ .4735 NS10-12.01H7-EB . 6 57,0 10,0 88,0 NFQF10

12,02 12,02 / 12,038 .4732/ .4739 NS10-12.02H7-EB . 6 57,0 10,0 88,0 NFQF10

12,03 12,03 / 12,048 .4736/ .4743 NS10-12.03H7-EB . 6 57,0 10,0 88,0 NFQF10

12,04 12,04 / 12,058 .4740/ .4747 NS10-12.04H7-EB . 6 57,0 10,0 88,0 NFQF10

12,05 12,05 / 12,068 .4744/ .4751 NS10-12.05H7-EB . 6 57,0 10,0 88,0 NFQF10

.关于切削参数,参见第 285 页 .关于导向槽型 EB45 或 EB845 的选择,参见第 272 页

DC 产品型号 尺. mm

.体规格 槽型 材质等级

OAL LUX DMM H15 RX2000 RN2010 RM2020 RM2090 RS2090

2,97-3,05 NS06-2.970-XX-XXXX 45,0 25,0 6,0 4 NFQF06-xx EB45 EB845 ] ] ] ] ] ]

3,051-6,05 NS06-3.051-XX-XXXX 50,0 30,0 6,0 4 NFQF06-xx EB45 EB845 ] ] ] ] ] ]

6,051-8,05 NS10-6.051-XX-XXXX 78,0 46,0 10,0 6 NFQF10-xx EB45 EB845 ] ] ] ] ] ]

10,051-12,05 NS10-10.051-XX-XXXX 88,0 57,0 10,0 6 NFQF10-xx EB45 EB845 ] ] ] ] ] ]

= 非标准库存。供货情况请参照新的价格和库存表注]意:在订购非标 Nano.x 铰刀时,请注明要铰削的孔的直径和公差。 订购.例: NS10-10,187/10,213-EB845, RS2090

Nano.x .杆 - 公制

订购代码02729036

产品型号NFQF06-03700-10N1

DC 2,97-6,05 DMM 10 BD 16 LU 37 LBN 80

02729037

NFQF06-03300-12N1

2,97-6,05 12 16 35 80

02729041

NFQF06-03000-16N1

2,97-6,05 16 16 30 80

02729044

NFQF10-05200-12N1

6,051-12,05 12 23 52 100

02729045

NFQF10-04900-16N1

6,051-12,05 16 23 49 100

02729046

NFQF10-04700-20N1

6,051-12,05 20 23 47 100

标准长度 短型

DC OAL OAL

2,970-3,050 124,5 109,5

3,051-6,050 144,5 113,5

6,051-8,050 189,5 152,5

8,051-10,050 199,5 152,5

10,051-12,050 219,5 162,5

2,97-6,050 备.夹紧套装NF06-CLKI

扳.

CLC06KEY

6,051-12,050 NF10-CLKI

CLC10KEY

.于 Nano.x .杆的备.夹紧套装包括:

- 1 个夹紧螺母- 1 个轴向止动弹簧圈

- 3 个锁紧钢珠(对于 NF06 规格,其直径为 3.5 mm;对于 NF10 规格,其直径为 5 mm)

- 1 个安全钢珠(对于 NF06 规格,其直径为 3 mm;对于 NF10 规格,其直径为 4 mm)

- 1 个 O 形圈注意:上图未显示安全钢珠。

切削参数 – NF/NS…-EB845

z=4 z=6 z=4 z=6 H15 CP20 RX2000

P3 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 - 60 (30-100) 80 (30-150)

P4 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 - 50 (30-80) 60 (30-120)

P5 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 20 (10-25) 50 (30-80) 60 (30-120)

P6 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 20 (10-25) 50 (30-80) 60 (30-120)

P7 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 20 (10-25) 50 (30-80) 60 (30-120)

P8 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 15 (10-20) 35 (20-60) 40 (20-80)

P11 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 15 (10-20) 35 (20-60) 40 (20-80)

P12 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 12 (8-15) 25 (15-45) 30 (15-65)

M1 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 12 (9-15) 25 (15-40) 35 (20-60)

M2 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 25 (15-40) 35 (20-60)

M3 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 25 (15-40) 35 (20-60)

M4 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 20 (10-30) 25 (15-40)

M5 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 20 (10-30) 25 (15-40)

K1 NF/NS-EB845 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 25 (15-30) 60 (40-100) 80 (30-150)

K2 NF/NS-EB845 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 - 25 (20-40) 40 (30-70)

K3 NF/NS-EB845 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 25 (15-30) 60 (40-100) 80 (30-150)

K4 NF/NS-EB845 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 25 (15-30) 45 (30-70) 70 (40-120)

K5 NF/NS-EB845 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 25 (15-30) 45 (30-70) 70 (40-120)

K6 NF/NS-EB845 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 - 60 (40-100) 80 (30-150)

K7 NF/NS-EB845 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 - 60 (40-100) 80 (30-150)

S1 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - 15 (8-20) 20 (10-25)

S2 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - 15 (8-20) 20 (10-25)

S3 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - 15 (8-20) 20 (10-25)

S11 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 20 (15-30) 30 (15-40) 40 (20-50)

S12 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 20 (15-30) 30 (15-40) 40 (20-50)

S13 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 20 (15-30) 30 (15-40) 40 (20-50)

H3 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H5 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H7 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H8 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H11 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H12 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H21 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H31 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

PM1 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 - 50 (30-80) 70 (40-100)

PM2 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 - 50 (30-80) 70 (40-100)

PM3 NF/NS-EB845 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 - 50 (30-80) 70 (40-100)

切削参数 – NF/NS-EB25

P1 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,9 0,5-1,2 25 (15-30) 60 (30-100) 80 (30-150)

P2 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,9 0,5-1,2 25 (15-30) 60 (30-100) 80 (30-150)

P3 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,9 0,5-1,2 25 (15-30) 60 (30-100) 80 (30-150)

P4 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,7 0,5-1 20 (10-25) 50 (30-80) 60 (30-120)

P5 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,7 0,5-1 20 (10-25) 50 (30-80) 60 (30-120)

P6 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,7 0,5-1 20 (10-25) 50 (30-80) 60 (30-120)

P7 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,7 0,5-1 20 (10-25) 50 (30-80) 60 (30-120)

M1 NF/NS-EB25 0,08-0,15 0,10-0,15 0,3-0,7 0,5-1 - 25 (15-40) 35 (20-60)

K1 NF/NS-EB25 0,10-0,20 0,10-0,25 0,3-0,9 0,5-1,2 25 (15-30) 60 (40-100) 80 (30-150)

K2 NF/NS-EB25 0,10-0,20 0,10-0,25 0,3-0,9 0,5-1,2 25 (20-40) 40 (30-70)

K3 NF/NS-EB25 0,10-0,20 0,10-0,25 0,3-0,9 0,5-1,2 25 (15-30) 60 (40-100) 80 (30-150)

K4 NF/NS-EB25 0,10-0,20 0,10-0,25 0,3-0,9 0,5-1,2 25 (15-30) 45 (30-70) 70 (40-120)

K5 NF/NS-EB25 0,10-0,20 0,10-0,25 0,3-0,9 0,5-1,2 25 (15-30) 45 (30-70) 70 (40-120)

K6 NF/NS-EB25 0,10-0,20 0,10-0,25 0,3-0,9 0,5-1,2 - 60 (40-100) 80 (30-150)

K7 NF/NS-EB25 0,10-0,20 0,10-0,25 0,3-0,9 0,5-1,2 - 60 (40-100) 80 (30-150)

N1 NF/NS-EB25 0,10-20 0,10-0,30 0,3-0,9 0,5-1,2 50 (20-80) - -

N2 NF/NS-EB25 0,10-20 0,10-0,30 0,3-0,9 0,5-1,2 50 (20-80) - -

N3 NF/NS-EB25 0,10-20 0,10-0,30 0,3-0,9 0,5-1,2 50 (20-80) - -

N11 NF/NS-EB25 0,10-20 0,10-0,30 0,3-0,9 0,5-1,2 50 (20-80) - -

PM1 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,9 0,5-1,2 - 50 (30-80) 70 (40-100)

PM2 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,9 0,5-1,2 - 50 (30-80) 70 (40-100)

PM3 NF/NS-EB25 0,10-0,15 0,1-0,20 0,3-0,9 0,5-1,2 - 50 (30-80) 70 (40-100)

切削参数 – NF/NS…-EB45

P1 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 25 (15-30) 60 (30-100) 80 (30-150)

P2 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 25 (15-30) 60 (30-100) 80 (30-150)

P3 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 25 (15-30) 60 (30-100) 80 (30-150)

P4 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 20 (10-25) 50 (30-80) 60 (30-120)

P5 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 20 (10-25) 50 (30-80) 60 (30-120)

P6 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 20 (10-25) 50 (30-80) 60 (30-120)

P7 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 20 (10-25) 50 (30-80) 60 (30-120)

P8 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 15 (10-20) 35 (20-60) 40 (20-80)

P11 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 15 (10-20) 35 (20-60) 40 (20-80)

P12 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 12 (8-15) 25 (15-45) 30 (15-65)

M1 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 12 (9-15) 25 (15-40) 35 (20-60)

M2 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 25 (15-40) 35 (20-60)

M3 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 25 (15-40) 35 (20-60)

M4 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 20 (10-30) 25 (15-40)

M5 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 20 (10-30) 25 (15-40)

K1 NF/NS-EB45 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 25 (15-30) 60 (40-100) 80 (30-150)

K2 NF/NS-EB45 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 - 25 (20-40) 40 (30-70)

K3 NF/NS-EB45 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 25 (15-30) 60 (40-100) 80 (30-150)

K4 NF/NS-EB45 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 25 (15-30) 45 (30-70) 70 (40-120)

K5 NF/NS-EB45 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 25 (15-30) 45 (30-70) 70 (40-120)

K6 NF/NS-EB45 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 - 60 (40-100) 80 (30-150)

K7 NF/NS-EB45 0,10-0,20 0,10-0,25 0,10-0,30 0,20-0,60 - 60 (40-100) 80 (30-150)

N1 NF/NS-EB45 0,10-20 0,10-0,30 0,10-0,30 0,20-0,60 50 (20-80) - 80 (30-150)

N2 NF/NS-EB45 0,10-20 0,10-0,30 0,10-0,30 0,20-0,60 50 (20-80) - 80 (30-150)

N3 NF/NS-EB45 0,10-20 0,10-0,30 0,10-0,30 0,20-0,60 50 (20-80) - 80 (30-150)

N11 NF/NS-EB45 0,10-20 0,10-0,30 0,10-0,30 0,20-0,60 50 (20-80) - 80 (30-150)

S1 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - 15 (8-20) 20 (10-25)

S2 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - 15 (8-20) 20 (10-25)

S3 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - 15 (8-20) 20 (10-25)

S11 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 20 (15-30) 30 (15-40) 40 (20-50)

S12 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 20 (15-30) 30 (15-40) 40 (20-50)

S13 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 20 (15-30) 30 (15-40) 40 (20-50)

H3 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H5 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H7 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H8 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H11 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H12 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H21 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

H31 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 10 (8-15)

PM1 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 - 50 (30-80) 70 (40-100)

PM2 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 - 50 (30-80) 70 (40-100)

PM3 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,20 0,20-0,50 - 50 (30-80) 70 (40-100)

TS1 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 20 (15-25) - 40 (20-60)

TS2 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 20 (15-25) - 40 (20-60)

TS3 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 20 (15-25) - 40 (20-60)

TS4 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 20 (15-25) - 40 (20-60)

TP1 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 20 (15-25) - 40 (20-60)

TP2 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 20 (15-25) - 40 (20-60)

TP3 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 20 (15-25) - 40 (20-60)

TP4 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 20 (15-25) - 40 (20-60)

GR1 NF/NS-EB45 0,10-0,15 0,1-0,20 0,10-0,30 0,20-0,60 40 (80-20) - 60 (30-120)

z=4 z=6 z=4 z=6 RN2010 RM2020 RM2090 RS2090

M1 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 25 (15-40) 40 (20-60) -

M2 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 25 (15-40) 40 (20-60) -

M3 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 25 (15-40) 40 (20-60) -

M4 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 20 (10-30) 30 (15-40) -

M5 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 - 20 (10-30) 30 (15-40) -

N1 NF/NS-EB45 0,10-0,20 0,10-0,30 0,10-0,30 0,20-0,60 50 (20-80) - - -

N2 NF/NS-EB45 0,10-0,20 0,10-0,30 0,10-0,30 0,20-0,60 50 (20-80) - - -

N3 NF/NS-EB45 0,10-0,20 0,10-0,30 0,10-0,30 0,20-0,60 50 (20-80) - - -

N11 NF/NS-EB45 0,10-0,20 0,10-0,30 0,10-0,30 0,20-0,60 50 (20-80) - - -

S1 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - - 20 (10-25)

S2 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - - 20 (10-25)

S3 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - - 25 (10-25)

S11 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - - 30 (20-50)

S12 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - - 30 (20-50)

S13 NF/NS-EB45 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - - 30 (20-50)

z=4 z=6 z=4 z=6 RM2020 RM2090 RS2090

M1 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 25 (15-40) 40 (20-60) -

M2 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 25 (15-40) 40 (20-60) -

M3 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 25 (15-40) 40 (20-60) -

M4 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 25 (10-30) 30 (15-40) -

M5 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,50 25 (10-30) 30 (15-40) -

S1 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 20 (10-25)

S2 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 20 (10-25)

S3 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 25 (10-25)

S11 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 30 (20-50)

S12 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 30 (20-50)

S13 NF/NS-EB845 0,08-0,15 0,10-0,15 0,10-0,20 0,20-0,30 - - 30 (20-50)

我们提供 Nano.x 铰刀和刀柄的非标设计。现在,您可以使用山高非标设计软件为您自己的中间直径 . 铰刀和非标 Nano.x 刀杆询价。易于操作:只需标明零件的大、小直径或使用软件中提供的 ISO 公差系统。自动生成 Nano.x 刀头产品型号。非标设计带给你不少便利:

修磨指南

Nano.x . β1 β2 β3 T

2,97-9,99 mm 8° 18° 8° 0,15 mm

10,00-12,050 mm 0,20 mm

规格:

金刚石砂轮颗粒度: D6 – 用于后角 (β1–β3)D64 – 用于第二后角 (β2)

重要

Bi. x. Bi. x.

Bi. x. . 范围 铰削深度 钻头 .公差 中间直径 表面粗糙度 (2)

SR80 .于通孔 6,875-60,500 mm 3–5–7 x D IT 6-7 是,通过非标设计提供 Ra 0,2–0,8 μm

SR81 .于盲孔 7,875–60,500 mm 3–5–7 x D IT 6-7 是,通过非标设计提供 Ra 0,2–0,8 μm

SR82 .于盲孔 短型 7,875–60,500 mm 2–3-5 x D IT 6-7 是,通过非标设计提供 Ra 0,2–0,8 μm

Bi. x.

除非另有要求,铰刀一般按照所要求公差的中值加工孔径。

铰刀类型:80 型:通孔81 型:盲孔导向槽型类型

82 型:盲孔,短型 EN1、EN2、EN3

孔径与精度 柄部型式:(当所需的型式不是标准型式时需注明)SR80 和 SR81:R1 不带削平面,标准型SR82R9 带削平面,标准型

产品型号编码 - . 重要:铰刀与刀片必须有相同的导向。

刀片规格:切削前角: P00, P0, P1

0°, 6°, 12° P2, P4

导向槽型类型硬质合金材质等级:EN1、EN2、EN3 CP20、H15

调整和加.参数 旋转式刀具

大推荐跳动量:0,02 mm.推荐高精度刀柄:液压夹头刀柄、D 型弹簧夹头刀柄、5672 弹簧夹头刀柄或热胀刀柄。

.于优化排屑

静止式刀具的推荐刀片朝向(见下图,从刀具前部观察)。

为获得佳的刀具寿命与孔径,应遵循下列冷却液要求。推荐使用内冷却。如果铰削深度 < 2 x D,则可以使用外部冷却液供应。矿物油含量少为 40% 的优质可溶油。加工不锈钢时推荐使用纯矿物油。小浓度为 6–8%。过滤 30–50 μm。对于铰刀直径而言,小流量为 0,5 l/min/mm。(例:铰刀直径为 . 10,小流量为 5 l/min)。

调整夹具

SF-60200-C160C190:零件号 02885396

- 水平架

- 直径 . 小于 60 mm 时的- 2 个千分表

- 大刀具直径 .:60,5 mm- 大刀具长度:200 mm

.选择 – 选择导向槽型

EN1 - 通.信息

大加工余量 . 0,5 mm。表面粗糙度 + (Ra 0,3 - 0,8 m)

EN2 - 短导向

大加工余量 . 0,3 mm。表面粗糙度 (Ra 0,4–1,2 m)。进给量大值 0,2 mm/rev。仅适用于要求使用短导向的场合。设计成端面切削。

EN3 - 极佳的表面质量

大加工余量 . 0,5 mm。表面粗糙度 (Ra 0,2-0,6 m)。适用于除铝合金外的所有材料。当 Ra < 0,3–0,4 m 时使用。

注意铰刀与刀片必须有相同的导向槽型。

材质等级与前角

使用第 475 页上的表格将工件材料划分到山高材料组中。使用第 303-305 页上的刀片与切削参数推荐表来选择材质和前角。刀片清单参见第 301 页。

Bi. x. – SR80

.于通孔 . 6H6-26H6 – .杆类型 R1, 不带削平面的圆柱柄

.刀片信息参见第 301 页 .内冷通道

DC7 产品型号SR80-7H6-EN1

尺. mm .规格 P0-EN1-xx

OAL 105 LS 40 LUX 63 LU 25 DMM 10

8 SR80-8H6-EN1

115 40 73 25 10 P0-EN1-xx

9 SR80-9H6-EN1

115 40 73 25 10 P1-EN1-xx

10 SR80-10H6-EN1

115 40 74 25 10 P1-EN1-xx

11 SR80-11H6-EN1

133 48 81 25 16 P1-EN1-xx

12 SR80-12H6-EN1

13 SR80-13H6-EN1

133 48 81 25 16 P2-EN1-xx

14 SR80-14H6-EN1

15 SR80-15H6-EN1

133 48 82 25 16 P2-EN1-xx

16 SR80-16H6-EN1

17 SR80-17H6-EN1

155 50 100 25 20 P2-EN1-xx

18 SR80-18H6-EN1

19 SR80-19H6-EN1

20 SR80-20H6-EN1

155 50 100 30 20 P4-EN1-xx

21 SR80-21H6-EN1

191 56 128 30 25 P4-EN1-xx

22 SR80-22H6-EN1

191 56 129 30 25 P4-EN1-xx

23 SR80-23H6-EN1

24 SR80-24H6-EN1

25 SR80-25H6-EN1

26 SR80-26H6-EN1

适.钻头直径 (mm)7-8 压板SR-B0

压板螺钉LH2040

.撑球BB1.5

调节螺钉SH2020

调整扳.0.9 SMS795 扭矩扳.*- 扭矩值 -

9 SR-B1

LH2540

BB2.0

SH2025 1.3 SMS795 H00-1305

10-12 SR-B2

SH2525

1.3 SMS795 H00-1305

13-19 SR-B3

LH3050

BB2.5

SH2540 1.5 SMS795 H00-1509

20-60 SR-B5

LH4010

BB3.0

SH3060 2SMS795

*扭矩扳手包含扳手芯

.于通孔 . 27H6–60H6 – .杆类型 R1, 不带削平面的圆柱柄

DC27 产品型号SR80-27H6-EN1

尺. mm .规格 P4-EN1-xx

OAL 221 LS 56 LUX 159 LU 30 DMM 25

28 SR80-28H6-EN1

221 56 159 30 25 P4-EN1-xx

29 SR80-29H6-EN1

30 SR80-30H6-EN1

31 SR80-31H6-EN1

221 56 160 30 25 P4-EN1-xx

32 SR80-32H6-EN1

34 SR80-34H6-EN1

226 56 165 30 25 P4-EN1-xx

35 SR80-35H6-EN1

36 SR80-36H6-EN1

226 56 166 30 25 P4-EN1-xx

38 SR80-38H6-EN1

40 SR80-40H6-EN1

42 SR80-42H6-EN1

226 56 167 30 25 P4-EN1-xx

44 SR80-44H6-EN1

48 SR80-48H6-EN1

226 56 168 30 25 P4-EN1-xx

50 SR80-50H6-EN1

52 SR80-52H6-EN1

226 56 169 30 25 P4-EN1-xx

54 SR80-54H6-EN1

58 SR80-58H6-EN1

60 SR80-60H6-EN1

适.钻头直径 (mm)20-60 压板SR-B5

压板螺钉LH4010

.撑球BB3.0

调节螺钉SH4060

扭矩扳.*H00-2020

扭矩值 2,0 Nm

.于通孔 – 中间直径 – .杆类型 R1, 不带削平面的圆柱柄

.刀片信息参见第 301 页 .重要!铰刀与刀片必须有相同的导向槽型 .关于导向槽型 EN1, EN2 或 EN3,参见第 292 页

DC6,875-7,874 产品型号SR80-6.875-XX-XXXX-EN 尺. mm .规格 P0-EN-xx

OAL 105 LS 40 LUX 63 LU 15 DMM 10

7,875-8,749 SR80-7.875-XX-XXXX-EN 115 40 73 25 10 P0-EN-xx

8,75-9,749 SR80-8.750-XX-XXXX-EN 115 40 73 25 10 P1-EN-xx

9,75-10,749 SR80-9.750-XX-XXXX-EN 115 40 73 25 10 P1-EN-xx

10,75-12,749 SR80-10.750-XX-XXXX-EN 133 48 81 25 16 P1-EN-xx

12,75-16,749 SR80-12.750-XX-XXXX-EN 133 48 81 25 16 P2-EN-xx

16,75-19,499 SR80-16.750-XX-XXXX-EN 155 50 100 25 20 P2-EN-xx

19,5-20,499 SR80-19.500-XX-XXXX-EN 155 50 100 30 20 P3-EN-xx

20,5-26,499 SR80-20.500-XX-XXXX-EN 191 56 129 30 25 P4-EN-xx

26,5-32,499 SR80-26.500-XX-XXXX-EN 221 56 160 30 25 P4-EN-xx

32,5-38,499 SR80-32.500-XX-XXXX-EN 226 56 165 30 25 P4-EN-xx

38,5-40,499 SR80-38.500-XX-XXXX-EN 226 56 166 30 25 P4-EN-xx

40,5-44,499 SR80-40.500-XX-XXXX-EN 226 56 167 30 25 P4-EN-xx

44,5-50,499 SR80-44.500-XX-XXXX-EN 226 56 168 30 25 P4-EN-xx

50,5-60,5 SR80-50.500-XX-XXXX-EN 226 56 169 30 25 P4-EN-xx

注意!当订购用于中间直径的铰刀时,请注明:被铰削孔的直径 . 与公差,导向槽型(EN1、EN2 或 EN3)。订购.例: SR80-11.50 H7-EN2, P1-EN2-06, CP20

适.钻头直径 (mm) 调节螺钉 压板 压板螺钉 调整扳.撑球

6,875-8,749 SH2020

SR-B0

LH2040

0.9SMS795 BB1.5

8,750-9,749 SH2525

SR-B1

1.3SMS795

9,750-12,749 SH2525

SR-B2

12,750-19,499 SH3040

SR-B3

1.5SMS795 BB2.0

19,500-60,500 SH4060

SR-B5

扭矩扳. –

H00-1305

* 需单独订购。 扭矩扳手包含扳手芯。

Bi. x. – SR81

.于盲孔 . 8H6–26H6 – .杆类型 R1, 不带削平面的圆柱柄

DC8 产品型号SR81-8H6-EN1

OAL 115 LS 40 LUX 73 LU 25 DMM 10

9 SR81-9H6-EN1

11 SR81-11H6-EN1

13 SR81-13H6-EN1

14 SR81-14H6-EN1

15 SR81-15H6-EN1

16 SR81-16H6-EN1

17 SR81-17H6-EN1

18 SR81-18H6-EN1

19 SR81-19H6-EN1

20 SR81-20H6-EN1

21 SR81-21H6-EN1

22 SR81-22H6-EN1

23 SR81-23H6-EN1

25 SR81-25H6-EN1

26 SR81-26H6-EN1

适.钻头直径 (mm)8 压板SR-B0

SH3040

1.5 SMS795 H00-1509

SH4060

.于盲孔 . 27H6–60H6 – .杆类型 R1, 不带削平面的圆柱柄

DC27 产品型号SR81-27H6-EN1

28 SR81-28H6-EN1

29 SR81-29H6-EN1

30 SR81-30H6-EN1

31 SR81-31H6-EN1

32 SR81-32H6-EN1

34 SR81-34H6-EN1

35 SR81-35H6-EN1

36 SR81-36H6-EN1

38 SR81-38H6-EN1

40 SR81-40H6-EN1

42 SR81-42H6-EN1

44 SR81-44H6-EN1

48 SR81-48H6-EN1

50 SR81-50H6-EN1

52 SR81-52H6-EN1

54 SR81-54H6-EN1

58 SR81-58H6-EN1

60 SR81-60H6-EN1

.于盲孔 – 中间直径 – .杆类型 R1, 不带削平面的圆柱柄

DC7,875-8,749 产品型号SR81-7.875-XX-XXXX-EN 尺. mm .规格 P0-EN-xx

8,75-9,749 SR81-8.750-XX-XXXX-EN 115 40 73 25 10 P1-EN-xx

9,75-10,749 SR81-9.750-XX-XXXX-EN 115 40 73 25 10 P1-EN-xx

10,75-12,749 SR81-10.750-XX-XXXX-EN 133 48 81 25 16 P1-EN-xx

12,75-16,749 SR81-12.750-XX-XXXX-EN 133 48 81 25 16 P2-EN-xx

16,75-19,499 SR81-16.750-XX-XXXX-EN 155 50 100 25 20 P2-EN-xx

19,5-20,499 SR81-19.500-XX-XXXX-EN 155 50 100 30 20 P4-EN-xx

20,5-26,499 SR81-20.500-XX-XXXX-EN 191 56 129 30 25 P4-EN-xx

26,5-32,499 SR81-26.500-XX-XXXX-EN 221 56 160 30 25 P4-EN-xx

32,5-38,499 SR81-32.500-XX-XXXX-EN 226 56 165 30 25 P4-EN-xx

38,5-40,499 SR81-38.500-XX-XXXX-EN 226 56 166 30 25 P4-EN-xx

40,5-44,499 SR81-40.500-XX-XXXX-EN 226 56 167 30 25 P4-EN-xx

44,5-50,499 SR81-44.500-XX-XXXX-EN 226 56 168 30 25 P4-EN-xx

50,5-60,5 SR81-50.500-XX-XXXX-EN 226 56 169 30 25 P4-EN-xx

注意!当订购用于中间直径的铰刀时,请注明:被铰削孔的直径 . 与公差,导向槽型(EN1、EN2 或 EN3)。订购.例: SR81-11.50 H7-EN2, P1-EN2-06, CP20

7,875-8,749 SH2020

8,75-9,749 SH2525

9,75-12,749 SH2525

12,75-19,499 SH3040

1.5SMS795 BB2.5

19,5-60,5 SH4060

Bi. x. – SR82

.于盲孔 – .于车削应.的短型系列 – .杆类型 R9, 带削平面的圆柱柄

DC7,875-8,749 产品型号SR82-7.875-XX-XXXX-EN 尺. mm .规格 P0-EN-xx

OAL 95 LS 40 LUX 53 LU 25 DMM 10

8,75-9,749 SR82-8.750-XX-XXXX-EN 95 40 53 25 10 P1-EN-xx

9,75-10,749 SR82-9.750-XX-XXXX-EN 95 40 53 25 10 P1-EN-xx

10,75-12,749 SR82-10.750-XX-XXXX-EN 113 40 61 25 16 P1-EN-xx

12,75-16,749 SR82-12.750-XX-XXXX-EN 113 48 61 25 16 P2-EN-xx

16,75-19,499 SR82-16.750-XX-XXXX-EN 113 48 60 25 20 P2-EN-xx

19,5-20,499 SR82-19.500-XX-XXXX-EN 115 50 60 30 20 P4-EN-xx

20,5-32,499 SR82-20.500-XX-XXXX-EN 115 50 89 30 25 P4-EN-xx

32,5-36,499 SR82-32.500-XX-XXXX-EN 151 56 105 30 25 P4-EN-xx

36,5-40,499 SR82-36.500-XX-XXXX-EN 166 56 106 30 25 P4-EN-xx

40,5-44,499 SR82-40.500-XX-XXXX-EN 166 56 107 30 25 P4-EN-xx

44,5-50,499 SR82-44.500-XX-XXXX-EN 166 56 108 30 25 P4-EN-xx

50,5-60,5 SR82-50.500-XX-XXXX-EN 166 56 109 30 25 P4-EN-xx

注意!当订购用于中间直径的铰刀时,请注明:被铰削孔的直径 . 与公差,导向槽型(EN1、EN2 或 EN3)。订购.例: SR82-11.50 H7EN2, P1-EN2-06, CP20

优化 / 材质使 .选择表来选择替换 .,获得更高.产率和安全性

.规格 钢件 不锈钢 铸铁 有.金属 铝合金 耐磨性

韧性 产品型号

.产率 通.性 安全性 . 材质等级

P0, P1, P2, P4

. . X Pxx-ENx-00 H15

. . . X Pxx-ENx-06 H15

. . . X Pxx-ENx-12 H15

. X Pxx-ENx-00 CP20

. . X Pxx-ENx-06 CP20

. . X Pxx-ENx-12 CP20

. . X Pxx-ENx-00 CP15

. . X Pxx-ENx-06 CP15

. . . . X Pxx-ENx-12 CP15

CP15 镀层耐磨材质等级,作为 CP20 的备选。针对铸铁与钢件的优化。也适用于有色金属。 Ti(C, N)

. 产品型号 材质等级

H15 CP20

P0

P0-EN1-0

00098229

00098244

P0-EN1-06

00091786

00091762

P0-EN1-12

00097299

00091971

P0-EN2-0

00098234

00098249

P0-EN2-06

00098160

00098170

P0-EN2-12

00098165

00098175

P0-EN3-0

00098239

00098254

P0-EN3-06

00098185

00098195

P0-EN3-12

00098190

00098200

P1

P1-EN1-0

00098230

00098245

P1-EN1-06

00091787

00091764

P1-EN1-12

00097300

00091972

P1-EN2-0

00098235

00098250

P1-EN2-06

00098161

00098171

P1-EN2-12

00098166

00098176

P1-EN3-0

00098240

00098255

P1-EN3-06

00098186

00094702

P1-EN3-12

00098191

00098201

P2

P2-EN1-0

00098231

00098246

P2-EN1-06

00091788

00091765

P2-EN1-12

00097301

00091973

P2-EN2-0

00098236

00098251

P2-EN2-06

00098162

00098172

P2-EN2-12

00098167

00098177

P2-EN3-0

00098241

00098256

P2-EN3-06

00098187

00098197

P2-EN3-12

00098192

00098202

P4

P4-EN1-0

00098232

00098247

P4-EN1-06

00091789

00091766

P4-EN1-12

00098128

00091974

P4-EN2-0

00098237

00098252

P4-EN2-06

00098163

00098173

P4-EN2-12

00098168

00098178

P4-EN3-0

00098242

00098257

P4-EN3-06

00098188

00098198

P4-EN3-12

00098193

00098203

我们提供 Bi.x 铰刀和刀柄的非标设计。现在,您可以使用山高非标设计软件为您自己的中间直径 . 铰刀和非标 Bi.x 刀柄询价。易于操作:只需标明零件的大、小直径或使用软件中提供的 ISO 公差系统。自动生成 Bi.x 刀头产品型号。非标设计带给你不少便利:

切削参数 – Pxx-EN1/EN2-00

. < 9 . ≥ 9 CP20 CP15

P5 Pxx-EN1/EN2-00 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-50) -

P6 Pxx-EN1/EN2-00 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-50) -

P7 Pxx-EN1/EN2-00 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-50) -

K1 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 90 (80-100) 120 (80-150)

K2 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 35 (25-50) 50 (25-70)

K3 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 90 (80-100) 120 (80-150)

K4 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 70 (60-80) 90 (80-100)

K5 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 70 (60-80) 90 (80-100)

K6 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 90 (80-100) 120 (80-150)

K7 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 90 (80-100) 120 (80-150)

PM1 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 50 (25-70) -

PM2 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 50 (25-70) -

PM3 Pxx-EN1/EN2-00 0,10-0,20 0,10-0,30 0,10-0,30 50 (25-70) -

切削参数 – Pxx-EN1/EN2-06

. < 9 . ≥ 9 H15 CP20 CP15

P1 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P2 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P3 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P4 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P5 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P6 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P7 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P8 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 30 (25-40) 50 (30-60) 60 (40-70)

P11 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 30 (25-40) 50 (30-60) 60 (40-70)

P12 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 40 (25-45) 45 (30-55)

M1 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 35 (25-40) 35 (25-40)

M2 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 35 (25-40) 35 (25-40)

M3 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 35 (25-40) 35 (25-40)

M4 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 20 (15-30) 30 (25-40) 30 (25-40)

M5 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 20 (15-30) 30 (25-40) 30 (25-40)

K1 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) 120 (80-150)

K2 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 35 (25-50) 50 (25-70)

K3 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) 120 (80-150)

K4 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 70 (60-80) 90 (80-100)

K5 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 70 (60-80) 90 (80-100)

K6 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) 120 (80-150)

K7 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) 120 (80-150)

N11 Pxx-EN1/EN2-06 0,10-0,30 0,20-0,50 0,10-0,30 65 (50-150) 90 (70-150) -

S1 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 - 25 (15-30) -

S2 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 - 25 (15-30) -

S3 Pxx-EN1/EN2-06 0,10-0,15 0,10-0,20 0,10-0,30 - 25 (15-30) -

PM1 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

PM2 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

PM3 Pxx-EN1/EN2-06 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

切削参数 – Pxx-EN1/EN2-12

P1 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P2 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P3 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P4 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P5 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P6 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P7 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P8 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 30 (25-40) 50 (30-60) 60 (40-70)

P11 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 30 (25-40) 50 (30-60) 60 (40-70)

P12 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 40 (25-45) 45 (30-55)

M1 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 35 (25-40) 35 (25-40)

M2 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 35 (25-40) 35 (25-40)

M3 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 35 (25-40) 35 (25-40)

M4 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 20 (15-30) 30 (25-40) 30 (25-40)

M5 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 20 (15-30) 30 (25-40) 30 (25-40)

K1 Pxx-EN1/EN2-12 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) -

K3 Pxx-EN1/EN2-12 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) -

K4 Pxx-EN1/EN2-12 0,10-0,20 0,10-0,30 0,10-0,30 - 70 (60-80) -

K5 Pxx-EN1/EN2-12 0,10-0,20 0,10-0,30 0,10-0,30 - 70 (60-80) -

N11 Pxx-EN1/EN2-12 0,10-0,30 0,20-0,50 0,10-0,30 65 (50-150) 90 (70-150) -

S1 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 - 25 (15-30) -

S2 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 - 25 (15-30) -

S3 Pxx-EN1/EN2-12 0,10-0,15 0,10-0,20 0,10-0,30 - 25 (15-30) -

PM1 Pxx-EN1/EN2-12 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

PM2 Pxx-EN1/EN2-12 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

PM3 Pxx-EN1/EN2-12 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

切削参数 – Pxx-EN3-00

P5 Pxx-EN3-00 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-50) -

P6 Pxx-EN3-00 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-50) -

P7 Pxx-EN3-00 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-50) -

K1 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 90 (80-100) 120 (80-150)

K2 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 35 (25-50) 50 (25-70)

K3 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 90 (80-100) 120 (80-150)

K4 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 70 (60-80) 90 (80-100)

K5 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 70 (60-80) 90 (80-100)

K6 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 90 (80-100) 120 (80-150)

K7 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 90 (80-100) 120 (80-150)

PM1 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 50 (25-70) -

PM2 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 50 (25-70) -

PM3 Pxx-EN3-00 0,10-0,20 0,10-0,30 0,10-0,30 50 (25-70) -

切削参数 – Pxx-EN3-06

P1 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P2 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P3 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P4 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P5 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P6 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P7 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P8 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 30 (25-40) 50 (30-60) 60 (40-70)

P11 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 30 (25-40) 50 (30-60) 60 (40-70)

P12 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 40 (25-45) 45 (30-55)

M1 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 - - 35 (25-40)

M2 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 - - 35 (25-40)

M3 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 - - 35 (25-40)

M4 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 - - 30 (25-40)

M5 Pxx-EN3-06 0,10-0,15 0,10-0,20 0,10-0,30 - - 30 (25-40)

K1 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) 120 (80-150)

K2 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 35 (25-50) 50 (25-70)

K3 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) 120 (80-150)

K4 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 70 (60-80) 90 (80-100)

K5 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 70 (60-80) 90 (80-100)

K6 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) 120 (80-150)

K7 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) 120 (80-150)

PM1 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

PM2 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

PM3 Pxx-EN3-06 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

切削参数 – Pxx-EN3-12

P1 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P2 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P3 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 40 (30-60) 105 (90-120) 120 (90-150)

P4 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P5 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P6 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P7 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 35 (25-40) 60 (40-70) 80 (60-100)

P8 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 30 (25-40) 50 (30-60) 60 (40-70)

P11 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 30 (25-40) 50 (30-60) 60 (40-70)

P12 Pxx-EN3-12 0,10-0,15 0,10-0,20 0,10-0,30 25 (20-30) 40 (25-45) 45 (30-55)

K1 Pxx-EN3-12 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) -

K3 Pxx-EN3-12 0,10-0,20 0,10-0,30 0,10-0,30 - 90 (80-100) -

K4 Pxx-EN3-12 0,10-0,20 0,10-0,30 0,10-0,30 - 70 (60-80) -

K5 Pxx-EN3-12 0,10-0,20 0,10-0,30 0,10-0,30 - 70 (60-80) -

PM1 Pxx-EN3-12 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

PM2 Pxx-EN3-12 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

PM3 Pxx-EN3-12 0,10-0,20 0,10-0,30 0,10-0,30 - 50 (25-70) -

调节指南

拧松两个调节螺钉 (7) 1/4 圈。

旋松两个锁紧螺钉 (5)。

彻底清洁 .座,然后对使.过的 .“2”进.转位或更换。

稳定地推动 .,使其紧靠轴向定位面与调节球 (6)。

.地拧紧锁紧螺钉。(握住扳.短的.端以获得正确的扭矩)。

使.导向条 (3) 的圆柱型后端将 μm 千分表调零。

将 .后端设置到某.直径,以使倒锥达到 0.01 mm/10 mm 的 .长度(参见图 2)。

使.导向条 (3) 的圆柱型前端将 μm 千分表调零。

.千分表 A 将 .的前端设置为高出导向条 (3) 0.02 mm 或 0.015 mm,参见图 1。使.千分表 B 再次检查倒锥值(步骤 6 和 7)。

注意:如果在调整过程中超出了所需的直径,应重新调整以消除调节螺钉的间隙。 0,015 mm (. ≤ 10 mm)

0,020 mm (. > 10 mm)

用于直径调整的千分表 A 值

设定表

千分表 B千分表 A

X (mm)图 2

直径范围 刀片规格 前部千分表 A 后部千分表 B

5,900-6,874 P00 +15 +5

6,875-8,749 P0 +15 -5

8,750-10,000 P1 +15 -5

10,001-12,749 P1 +20 0

12,750-19,499 P2 +20 0

19,500-60,500 P4

+20 0

.千分表单位 = 1 μm .当在相邻的导向条上设置为零时,前、后千分表值有效

.后千分表值根据刀片的 1 μm/mm 倒锥计算

X. x.

X. x. . 范围 铰削深度 钻头 .公差 中间直径 表面粗糙度

39,500-154,500 mm 2,5–6,5 x D IT 6 是,通过非标设计提供 Ra 0,8–1,2 μm

X.x. 是山高专门开发的铰刀系列,专用于加工直径从 39.5 至 154.5 mm 的大孔。采用可获得 IT 6 级精度公差的可调和可转位刀片,以及可保证部件质量的内置可调跳动量适配器。对于大直径孔的铰削加工,多齿构造和拥有专利的预加载导向条提供大的稳定性与生产率。

特征

-4 或 8 个切削刃可优化所有材料的加工 -可靠的夹紧系统 -采用 1 个容易设定的调节螺钉,便于调整 -适用于不同应用的材质和槽型选项

-拥有专利的预加载导向条系统可确保应用场合的稳定性 -导向条润滑用于确保性能和安全性

-集成的可调转接头,可获得理想的跳动量控制

-山 高刀柄系统样本中的刀杆和接长杆系列可以提供优的基础柄性能

产品型号编码 - .柄

法兰规格 长度 刀杆类型

产品型号编码 - 标准.头

刀头类型 直径和公差 齿数 法兰规格 D

产品型号编码 - 中间直径.头

刀头类型:

- HF85,通孔,短切屑材料- HF85B,盲孔,短切屑材料- HF86,通孔,所有材料- HF86B,盲孔,所有材料

产品型号编码 - .

刀片规格 导向槽型 前角 材质等级

用于 HF85 和 HF 85B X.x 刀头的 RNAX 刀片

用于 HF86 和 HF86B X.x 刀头的 LNEG 刀片

RNAX

. 产品型号 材质等级 前角

RX1500 RX2000

RNAX1005-EB1570-03

02687601

02687603

3 °

RNAX1005-EB45-03

02687600

02688608

RNAX1005-EB845-03

02687593

02688606

LNEG

RX1500 RX2000 CF

LNEG1003-EB45-03

02781311

LNEG1003-EB45-06

02904277

02781313

02904276

6 °

LNEG1003-EB845-03

02781314

LNEG1003-EB845-06

02781315

应.

导向槽型 - EB45

切屑控制 +++表面粗糙度 + (Ra 1,2 - 2 m)槽型

切屑控制 ++表面粗糙度 +++ (Ra 0,4 - 1,2 m)

导向槽型 - EB1570

切屑控制 ++表面粗糙度 ++ (R 0,8 - 1,6 m)适用于长悬伸应用a的稳定性 +++

.于 RNAX .、通孔直径 .39,5-59,499 mm 的.头

.关于材质和槽型,参见第 313-314 页

DC39,5-44,499 产品型号HF85-39.5/44.499-03-32 尺. mm 3 0,41 . RNAX1005 .

LFS 33 DCON 32

44,5-49,499 HF85-44.5/49.499-03-32 33 32 3 0,51 RNAX1005 .

49,5-54,499 HF85-49.5/54.499-03-32 33 32 3 0,62 RNAX1005 .

54,5-59,499 HF85-54.5/59.499-03-32 33 32 3 0,74 RNAX1005 .

适.镗头HF85 03-32 调节螺钉SH4075S

可调.夹CARTCYHF16

压板螺钉LDH4010

.螺钉C03010-T09P

扳. (旗型)H2.0-2D

楔块压板

B6027

适.镗头HF85 03-32 ./.夹锁紧扳.T00-09P20

扭矩扳.

* 需单独订购。

扭矩值 T00-09P20 (Nm): 2扭矩值 H00-2020 (Nm): 2

.于 RNAX .、盲孔直径 .39,5-59,499 mm 的.头

LFS DCON

39,5-44,499 HF85B-39.5/44.499-03-32 33 32 3 0,41 RNAX1005 .

44,5-49,499 HF85B-44.5/49.499-03-32 33 32 3 0,51 RNAX1005 .

49,5-54,499 HF85B-49.5/54.499-03-32 33 32 3 0,62 RNAX1005 .

54,5-59,499 HF85B-54.5/59.499-03-32 33 32 3 0,74 RNAX1005 .

适.镗头 调节螺钉 可调.夹 压板螺钉 .螺钉 扳. (旗型) 调整扳. 楔块压板

HF85B 03-32 SH4075S

CARTCYHF16B

LDH4010

C03010-T09P

H2.0-2D

适.镗头 ./.夹锁紧扳. 扭矩扳.

HF85B 03-32 T00-09P20

.于 LNEG .、通孔直径 .39,5-59,499 mm 的.头

DC39,5-44,499 产品型号HF86-39.5/44.499-03-32 尺. mm 3 0,41 . LNEG1003 .

44,5-49,499 HF86-44.5/49.499-03-32 33 32 3 0,51 LNEG1003 .

49,5-54,499 HF86-49.5/54.499-03-32 33 32 3 0,62 LNEG1003 .

54,5-59,499 HF86-54.5/59.499-03-32 33 32 3 0,74 LNEG1003 .

适.镗头HF86 03-32 调节螺钉SH4075S

可调.夹CARTCYLN16

.螺钉C02506-T07P

适.镗头HF86 03-32 ./.夹锁紧扳.T00-07P09

扭矩值 T00-07P09 (Nm): 0,9扭矩值 H00-2020 (Nm): 2

.于 LNEG .、盲孔直径 .39,5-59,499 mm 的.头

DC39,5-44,499 产品型号HF86B-39.5/44.499-03-32 尺. mm 3 0,41 . LNEG1003 .

44,5-49,499 HF86B-44.5/49.499-03-32 33 32 3 0,51 LNEG1003 .

49,5-54,499 HF86B-49.5/54.499-03-32 33 32 3 0,62 LNEG1003 .

54,5-59,499 HF86B-54.5/59.499-03-32 33 32 3 0,74 LNEG1003 .

HF86B 03-32 SH4075S

CARTCYLN16B

C02506-T07P

适.镗头HF86B 03-32 ./.夹锁紧扳.T00-07P09

.于直径 .39,5-59,499 mm 的 Seco-Capto.杆

铰 .柄 产品型号

HF32-050-C3

LF min – LF max50 锥柄 C3 BD 32 0,258

HF32 .HSKA63

65 245 HSK-A63 32 –

HF32 .HSKA80

100 209 HSK-A80 32 –

HF32 .HSKA100

70 245 HSK-A100 32 –

HF32 .DIN40ADB 60 252 DIN40ADB 32 –

HF32 .DIN50ADB 60 317 DIN50ADB 32 –

HF32 .BT40ADB 65 252 BT40ADB 32 –

HF32 .BT50ADB 75 317 BT50ADB 32 –

.于 HF32-050-C3 的.杆和接长杆(更多信息,请参见山高刀具.柄系统样本)。

.杆 产品型号

C3-390.410-63075C

LF75 锥柄 HSK-A63 Seco-Capto规格 C3 0,893

C3-390.410-100080A

80 HSK-A100 C3 2,294

C3-390B.140-40030

30 DIN40 ADB C3 0,8

C3-390B.55-40030

30 BT40 ADB C3 0,9

C3-390B.55-40060

60 BT40 ADB C3 1,1

C3-390B.140-50030

30 DIN50 ADB C3 2,6

C3-390B.140-50060

60 DIN50 ADB C3 2,7

C3-390B.58-50040

40 BT50 ADB C3 3,5

C3-390B.58-50070

70 BT50 ADB C3 3,7

接长杆

C3-391.01-32060A

LF60 锥柄 C3 Seco-Capto规格 C3 0,336

C3-391.01-32080A

80 C3 C3 0,449

C4-391.02-32055A

55 C4 C3 0,418

C4-391.02-32070A

70 C4 C3 0,559

C5-391.02-32060A

60 C5 C3 0,637

C6-391.02-32070A

70 C6 C3 1,06

.于直径 .39,5-59,499 mm 的 Gra. ex .杆

铰刀刀柄

HF32-050-G3

LF min – LF max50 锥柄 G3 BD 32 0,32

.于 HF32-050-G3 的.杆和接长杆(更多信息,请参见山高刀具.柄系统样本)。

EM93044011850

LF50 锥柄HSK-A63 Gra.ex 规格 G3 0,73

EM93064011855

55 HSK-A100 G3 2,1

EM34694011835

35 DIN40 ADB G3 0,908

EM346940118100

100 DIN40 ADB G3 1,215

EM34144011840

40 BT40 ADB G3 1,061

EM341440118100

100 BT40 ADB G3 1,308

EM34714011835

35 DIN50 ADB G3 2,67

EM34164011845

45 BT50 ADB G3 3,58

EM341640118120

120 BT50 ADB G3 3,9

M402330

LF40 锥柄G3 Gra.ex 规格 G3 0,231

M402331

60 G3 G3 0,356

.于 RNAX .、通孔直径 .59,5-84,499 mm 的.头

DC59,5-64,499 产品型号HF85-59.5/64.499-05-55 尺. mm 5 1,3 . RNAX1005 .

LFS 50 DCON 55

64,5-69,499 HF85-64.5/69.499-05-55 50 55 5 1,5 RNAX1005 .

69,5-74,499 HF85-69.5/74.499-05-55 50 55 5 1,75 RNAX1005 .

74,5-79,499 HF85-74.5/79.499-05-55 50 55 5 2,0 RNAX1005 .

79,5-84,499 HF85-79.5/84.499-05-55 50 55 5 2,2 RNAX1005 .

适.镗头HF85 05-55 调节螺钉SH4075S

可调.夹CARTCYHF20

压板螺钉LDH4012

调整扳.4SMS795

适.镗头HF85 05-55 ./.夹锁紧扳.T00-09P20

.于 RNAX .、盲孔直径 .59,5-84,499 mm 的.头

59,5-64,499 HF85B-59.5/64.499-05-55 50 55 5 1,3 RNAX1005 .

64,5-69,499 HF85B-64.5/69.499-05-55 50 55 5 1,5 RNAX1005 .

69,5-74,499 HF85B-69.5/74.499-05-55 50 55 5 1,75 RNAX1005 .

74,5-79,499 HF85B-74.5/79.499-05-55 50 55 5 2,0 RNAX1005 .

79,5-84,499 HF85B-79.5/84.499-05-55 50 55 5 2,2 RNAX1005 .

HF85B 05-55 SH4075S

CARTCYHF20B

LDH4012

HF85B 05-55 T00-09P20

.于 LNEG .、通孔直径 .59,5-84,499 mm 的.头

DC59,5-64,499 产品型号HF86-59.5-64.499-05-55 尺. mm 5 1,3 . LNEG1003 .

64,5-69,499 HF86-64.5-69.499-05-55 50 55 5 1,5 LNEG1003 .

69,5-74,499 HF86-69.5-74.499-05-55 50 55 5 1,75 LNEG1003 .

74,5-94,499 HF86-74.5-79.499-05-55 50 55 5 2,0 LNEG1003 .

79,5-84,499 HF86-79.5-84.499-05-55 50 55 5 2,2 LNEG1003 .

适.镗头HF86 05-55 调节螺钉SH4075S

可调.夹CARTCYLN20

适.镗头HF86 05-55 ./.夹锁紧扳.T00-07P09

.于 LNEG .、盲孔直径 .59,5-84,499 mm 的.头

DC59,5-64,499 产品型号HF86B-59.5/64.499-05-55 尺. mm 5 1,3 . LNEG1003 .

64,5-69,499 HF86B-64.5/69.499-05-55 50 55 5 1,5 LNEG1003 .

69,5-74,499 HF86B-69.5/74.499-05-55 50 55 5 1,75 LNEG1003 .

74,5-79,499 HF86B-74.5/79.499-05-55 50 55 5 2,0 LNEG1003 .

79,5-84,499 HF86B-79.5/84.499-05-55 50 55 5 2,2 LNEG1003 .

适.镗头HF86B 05-55 调节螺钉SH4075S

可调.夹CARTCYLN20B

适.镗头HF86B 05-55 ./.夹锁紧扳.T00-07P09

.于直径 .59,5-84,499 mm 的 Seco-Capto.杆

HF55-080-C5

LF min – LF max80 锥柄 C5 BD 55 1,423

HF55 .HSKA63

80 239 HSK-A63 55 –

HF55 .HSKA80

100 239 HSK-A80 55 –

HF55 .HSKA100

100 239 HSK-A100 55 –

HF55 .DIN40ADB 80 239 DIN40ADB 55 –

HF55 .DIN50ADB 80 304 DIN50ADB 55 –

HF55 .BT40ADB 80 239 BT40ADB 55 –

HF55 .BT50ADB 80 304 BT50ADB 55 –

.于 HF55-080-C5 的.杆和接长杆(更多信息,请参见山高刀具.柄系统样本)。

C5-390.410-63090C

LF90 锥柄 HSK-A63 Seco-Capto规格 C5 1,402

C5-390.410-100100A

100 HSK-A100 C5 2,894

C5-390B.140-40040

40 DIN40 ADB C5 0,9

C5-390B.140-40080

80 DIN40 ADB C5 1,5

C5-390B.55-40050

50 BT40 ADB C5 1,1

C5-390B.55-40090

90 BT40 ADB C5 1,7

C5-390B.140-50030

30 DIN50 ADB C5 2,6

C5-390B.140-50070

70 DIN50 ADB C5 3,1

C5-390B.58-50040

40 BT50 ADB C5 3,4

C5-390B.58-50080

80 BT50 ADB C5 4,0

C5-391.01-50080A

LF80 锥柄 C5 Seco-Capto规格 C5 1,114

C5-391.01-50100A

100 C5 C5 1,39

C6-391.02-50080A

80 C6 C5 1,448

C6-391.02-50110A

110 C6 C5 2,15

C8-391.02-50080B

2,3196

.于直径 .59,5-84,499 mm 的 Gra. ex .杆

HF55-080-G5

LF min – LF max80 锥柄 G5 BD 55 1,278

.于 HF55-080-G5 的.杆和接长杆(更多信息,请参见山高刀具.柄系统样本)。

EM93044012860

LF60 锥柄HSK-A63 Gra.ex 规格 G5 0,975

EM930440128100

100 HSK-A63 G5 1,574

EM930440128140

140 HSK-A63 G5 2,182

EM93064012865

65 HSK-A100 G5 2,364

EM930640128110

110 HSK-A100 G5 3,02

EM930640128150

150 HSK-A100 G5 3,675

EM34694012840

40 DIN40 ADB G5 0,922

EM34694012880

80 DIN40 ADB G5 1,492

EM346940128120

120 DIN40 ADB G5 2,08

EM34144012845

45 BT40 ADB G5 1,112

EM34144012880

80 BT40 ADB G5 1,54

EM341440128120

120 BT40 ADB G5 2,12

EM34714012840

40 DIN50 ADB G5 2,748

EM341640128100

100 BT50 ADB G5 4,22

EM34164012855

55 BT50 ADB G5 4,0

EM341640128140

140 BT50 ADB G5 4,8

M402550

LF50 锥柄G5 Gra.ex 规格 G5 0,72

M402551

75 G5 G5 1,11

M402552

100 G5 G5 1,476

.于 RNAX .、通孔直径 .84,5-119,499 mm 的.头

DC84,5-89,499 产品型号HF85-84.5/89.499-07-80 尺. mm 7 1,68 . RNAX1005 .

LFS 50 DCON 80

89,5-94,499 HF85-89.5/94.499-07-80 50 80 7 1,85 RNAX1005 .

94,5-99,499 HF85-94.5/99.499-07-80 50 80 7 2,02 RNAX1005 .

99,5-104,499 HF85-99.5/104.499-07-80 50 80 7 2,2 RNAX1005 .

104,5-109,499 HF85-104.5/109.499-07-80 50 80 7 2,4 RNAX1005 .

109,5-114,499 HF85-109.5/114.499-07-80 50 80 7 2,61 RNAX1005 .

114,5-119,499 HF85-114.5/119.499-07-80 50 80 7 2,82 RNAX1005 .

适.镗头HF85 07-80 调节螺钉SH4075S

适.镗头HF85 07-80 ./.夹锁紧扳.T00-09P20

.于 RNAX .、盲孔直径 .84,5-119,499 mm 的.头

DC84,5-89,499 产品型号HF85B-84.5/89.499-07-80 尺. mm 7 1,68 . RNAX1005 .

89,5-94,499 HF85B-89.5/94.499-07-80 50 80 7 1,85 RNAX1005 .

94,5-99,499 HF85B-94.5/99.499-07-80 50 80 7 2,02 RNAX1005 .

99,5-104,499 HF85B-99.5/104.499-07-80 50 80 7 2,2 RNAX1005 .

104,5-109,499 HF85B-104.5/109.499-07-80 50 80 7 2,4 RNAX1005 .

109,5-114,499 HF85B-109.5/114.499-07-80 50 80 7 2,61 RNAX1005 .

114,5-119,499 HF85B-114.5/119.499-07-80 50 80 7 2,82 RNAX1005 .

适.镗头HF85B 07-80 调节螺钉SH4075S

可调.夹CARTCYHF20B

适.镗头HF85B 07-80 ./.夹锁紧扳.T00-09P20

.于 LNEG .、通孔直径 .84,5-119,499 mm 的.头

DC84,5-89,499 产品型号HF86-84.5/89.499-07-80 尺. mm 7 1,68 . LNEG1003 .

89,5-94,499 HF86-89.5/94.499-07-80 50 80 7 1,85 LNEG1003 .

94,5-99,499 HF86-94.5/99.499-07-80 50 80 7 2,02 LNEG1003 .